LEMON Manuals: Even more car manuals for everyone
Home >> Chevrolet >> 2015 >> Cruze LT, Automatic Trans >> Repair and Diagnosis >> External Pages >> Different variant/trim >> Section 10 (Engine Controls And Fuel - 1.8L (LUW, LWE) - DTC P0010 To DTC P0442) >> Diagnostic Information and Procedures >> DTC P0097, P0098 or P0099: Intake Air Temperature (IAT) Sensor 2 Circuit >> Circuit/System Testing

Circuit/System Testing

WARNING: This page is about a different variant/trim than selected.
NOTE: You must perform Circuit/System Verification  before proceeding with Circuit/System Testing.
  1. Ignition OFF, disconnect the harness connector at the B75C Multifunction Intake Air sensor.
  2. Ignition OFF and all systems OFF. It may take up to for 2 minutes for all vehicle systems to power down. Test for less than 2 Ω between the low reference circuit terminal 7 and ground.
    • If 2 Ω or greater 
    1. Ignition OFF, disconnect the harness connector at the K20 Engine Control Module.
    2. Test for less than 2 Ω in the low reference circuit end to end.
      • If 2 Ω or greater, repair the open or high resistance in the circuit.
      • If less than 2 Ω replace the K20 Engine Control Module.
    • If less than 2 Ω 
  3. Ignition ON, test for 4.8-5.2 V between the intake air temperature signal 2 circuit terminal 1 and ground.
    • If less than 4.8 V 
    1. Ignition OFF, disconnect the harness connector at the K20 Engine Control Module.
    2. Test for infinite resistance between the signal circuit and ground.
      • If less than infinite resistance, repair the short to ground on the circuit.
      • If infinite resistance
    3. Test for less than 2 Ω in the signal circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, replace the K20 Engine Control Module.
    • If greater than 5.2 V 
    1. Ignition OFF, disconnect the harness connector at the K20 Engine Control Module.
      NOTE: If the signal circuit is shorted to a voltage the engine control module or the sensor may be damaged.
    2. Ignition ON, test for less than 1 V between the signal circuit and ground.
      • If 1 V or greater, repair the short to voltage on the circuit.
      • If less than 1 V, replace the K20 Engine Control Module.
    • If between 4.8-5.2 V 
  4. Ignition ON, test for 4.8-5.2 V between the IAT 2 signal terminal 1 and ground.
    • If less than 4.8 V 
    1. Ignition OFF, disconnect the harness connector at the K20 Engine Control Module.
    2. Test for infinite resistance between the signal circuit and ground.
      • If less than infinite resistance, repair the short to ground on the circuit.
      • If infinite resistance
    3. Test for less than 2 Ω in the signal circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, replace the K20 Engine Control Module.
    • If greater than 5.2 V 
    1. Ignition OFF, disconnect the harness connector at the K20 Engine Control Module.
      NOTE: If the signal circuit is shorted to a voltage the engine control module or the sensor may be damaged.
    2. Ignition ON, test for less than 1 V between the signal circuit and ground.
      • If 1 V or greater, repair the short to voltage on the circuit.
      • If less than 1 V, replace the K20 Engine Control Module.
    • If between 4.8-5.2 V 
  5. Determine if EL-38522-A  Variable Signal Generator or equivalent is available.
    • EL-38522-A, Variable Signal Generator; or equivalent is not available 
    1. Replace the K20 Engine Control Module.
    2. Operate the vehicle within the Conditions for Running the DTC. You may also operate the vehicle within the conditions that you observed from the freeze frame/failure records data.
    3. Verify the DTC does not set.
      • If the DTC sets 

        Refer to step  9.

      • If the DTC does not set 
    4. All OK.
    • EL-38522-A, Variable Signal Generator; or equivalent is available 
  6. Ignition OFF, connect the leads of the EL-38522-A  Variable Signal Generator as follows:
    • Red lead to the signal circuit terminal 1 at the harness connector
    • Black leads to ground
    • Battery voltage supply lead to B+
  7. Set the EL-38522-A  Variable Signal Generator to the following specifications.
    • Signal switch to 5 V
    • Duty Cycle switch to 50 % (Normal)
    • Frequency switch to 30 Hz
  8. Ignition ON, verify the scan tool IAT Sensor 2 parameter is between 28-32 Hz.
    • If not between 28-32 Hz 

      Replace the K20 Engine Control Module.

    • If between 28-32 Hz 
  9. Test or replace the B75C Multifunction Intake Air sensor.
scientia non olet · About LEMON Manuals