LEMON Manuals: Even more car manuals for everyone
Home >> Chevrolet >> 2015 >> Cruze LT, Automatic Trans >> Repair and Diagnosis >> External Pages >> Different car >> Section 89 (Engine Controls And Fuel - 1.4L (LUJ LUV) - DTC P0010 To DTC P0246) >> Diagnostic Information and Procedures >> DTC P0112, P0113, or P0114: Intake Air Temperature (IAT) Sensor >> Circuit/System Testing

Circuit/System Testing

WARNING: This page is about a different car, the 2015 Chevrolet Trax and 2015 Buick Encore. However, it is still accessible from the selected car via links, so may be relevant.
NOTE:

You must perform the Circuit/System Verification before proceeding with Circuit/System Testing.

  1. Ignition OFF, and all vehicle systems OFF, it may take up to 2 min. for all vehicle systems to power down. Disconnect the harness connector at the B75C Multifunction Intake Air sensor.
  2. Test for less than 2 Ω between the low reference circuit terminal 7 and ground.
    • If 2 Ω or greater 
    1. Ignition OFF, disconnect the harness connector at the K20 Engine Control Module.
    2. Test for less than 2 Ω in the low reference circuit end to end.
      • If 2 Ω or greater, repair the open or high resistance in the circuit.
      • If less than 2 Ω replace the K20 Engine Control Module.
    • If less than 2 Ω 
  3. Ignition ON, test for 4.8-5.2 V between signal circuit terminal 8 and ground.
    • If less than 4.8 V 
    1. Ignition OFF, disconnect the harness connector at the K20 Engine Control Module.
    2. Test for infinite resistance between the signal circuit and ground.
      • If less than infinite resistance, repair the short to ground on the circuit.
      • If infinite resistance
    3. Test for less than 2 Ω in the signal circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, replace the K20 Engine Control Module.
    • If greater than 5.2 V 
      NOTE:

      If the signal circuit is shorted to a voltage the engine control module or the sensor may be damaged.

    1. Ignition OFF, disconnect the harness connector at the K20 Engine Control Module.
    2. Ignition ON, test for less than 1 V between the signal circuit and ground.
      • If 1 V or greater, repair the short to voltage on the circuit.
      • If less than 1 V, replace the K20 Engine Control Module.
    • If between 4.8-5.2 V 
  4. Ignition ON, verify the scan tool IAT Sensor 1 parameter is colder than -39°C (-38°F).
    • If warmer than -39°C (-38°F). 
    1. Ignition OFF, disconnect the harness connector at the K20 Engine Control Module.
    2. Test for infinite resistance between the signal circuit terminal 8 and ground.
      • If less than infinite resistance, repair the short to ground on the circuit.
      • If infinite resistance
    3. Test for less than 2 Ω in the signal circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, replace the K20 Engine Control Module.
    • If colder than -39°C (-38°F). 
  5. Ignition OFF, install a 3 A fused jumper wire between the signal circuit terminal 8 and the low reference circuit terminal 7.
  6. Verify the scan tool IAT Sensor 1 parameter is warmer than 148°C (298°F).
    • If colder than 148°C (298°F). 
    1. Ignition OFF, remove the jumper wire, disconnect the harness connector at the K20 Engine Control Module, ignition ON.
    2. Test for less than 1 V between the signal circuit and ground.
      • If 1 V or greater, repair the short to voltage on the circuit.
      • If less than 1 V
    3. Ignition OFF.
    4. Test for less than 2 Ω in the signal circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, replace the K20 Engine Control Module.
    • If warmer than 148°C (298°F). 
  7. Test or replace the B75C Multifunction Intake Air sensor.
scientia non olet · About LEMON Manuals