LEMON Manuals: Even more car manuals for everyone
Home >> Chevrolet >> 2015 >> Cruze LT, Automatic Trans >> Repair and Diagnosis >> External Pages >> Different car >> Section 55 (Engine Mechanical - 1.4L (LUV)) >> Repair Instructions - Off Vehicle >> Engine Front Cover and Oil Pump Assemble >> Oil Pump Installation

Oil Pump Installation

WARNING: This page is about a different car, the 2015 Chevrolet Trax and 2015 Buick Encore. However, it is still accessible from the selected car via links, so may be relevant.
    Fig 1: Oil Pump Components
    GM2191079Courtesy of GENERAL MOTORS COMPANY
    NOTE:

    The oil pump slide spring and pin, as well as the slide seal and slide seal spring can be ordered as single parts. All other oil pump components can only be ordered as a replacement kit.

  1. Install the oil pump components in the following order:
      NOTE:

      The bore (8) in the oil pump slide must fit smooth-running and without clearance to the oil pump slide pivot pin (7).

    1. Install the oil pump slide (6).
    2. Install the inner oil pump vane ring (5).
      3. NOTE:

      Mind the installation position of the oil pump vane rotor (4). The mark (9) must point to direction of the oil pump cover.

    3. Install the oil pump vane rotor (4).
      4. NOTE:

      Mind the localized flats (3) on the oil pump vanes (2) caused by the oil pump vane rings. The localized flats must point to the oil pump vane rotor.

    4. Install the 6 oil pump vanes (2).
    5. Install the outer oil pump vane ring (1).
    2. Fig 2: Oil Pump Slide Seal Springs And Grooves
    GM2191049Courtesy of GENERAL MOTORS COMPANY
  2. Install the 2 oil pump slide seals and the 2 oil pump slide seal springs (2) in the position as shown to the 2 grooves (1) of the oil pump slide.
    3. Fig 3: Oil Pump Slide Spring, Pin, Chambers And Front Cover Edge
    GM2191052Courtesy of GENERAL MOTORS COMPANY
  3. Protect the engine front cover edge (5) with a suitable piece of plastic.
    4. NOTE:

    The length of the removed oil pump slide spring (2) should be 76.5 mm (3.0118 in) for suction engines and 61 mm (2.4016 in) for turbo engines.

  4. Install the oil pump slide spring pin along with the oil pump slide spring (4). Use a screwdriver to compress the oil pump slide spring. The flat side of oil pump slide spring pin must face upwards.
  5. Measure the oil pump clearances to ensure a correct installation of the oil pump components. Refer to Engine Front Cover and Oil Pump Cleaning and Inspection .
  6. Lubricate the oil pump vanes, the oil pump vane rotor, the oil pump slide spring and the area (3) with engine oil.
  7. Inspect the oil pump slide spring mechanism for functionality.
    8. Fig 4: Engine Oil Pump Cover And Bolts
    GM2191037Courtesy of GENERAL MOTORS COMPANY
  8. Install the oil pump cover (2) and the 8 oil pump cover bolts (1).
    9. Fig 5: Oil Pump Cover Bolts Tightening Sequence
    GM2191056Courtesy of GENERAL MOTORS COMPANY
    CAUTION:

    Refer to Fastener Caution .

  9. Tighten the oil pump cover bolts in a sequence as shown to 8 N.m (71 lb in).
    10. Fig 6: Crankshaft Balancer
    GM2191058Courtesy of GENERAL MOTORS COMPANY
  10. Install the crankshaft balancer (1) and rotate in the direction shown (2) in order to inspect the function of the oil pump mechanism. The crankshaft balancer should rotate easily.
scientia non olet · About LEMON Manuals