LEMON Manuals: Even more car manuals for everyone
Home >> Chevrolet >> 2015 >> Cruze LT, Automatic Trans >> Repair and Diagnosis >> External Pages >> Different car >> Section 51 (Lighting System) >> Diagnostic Information and Procedures >> Dome Lamps Malfunction >> Circuit/System Testing

Circuit/System Testing

WARNING: This page is about a different car, the 2015 Chevrolet Trax and 2015 Buick Encore. However, it is still accessible from the selected car via links, so may be relevant.

Dome Lamp Switch Malfunction

  1. Ignition OFF, scan tool disconnected, all doors closed, all accessories OFF, disconnect the harness connector at the inoperative E37A Dome/Reading Lamps. It may take up to 2 min for all vehicle systems to power down.
  2. Test for less than 10 Ω between the ground circuit terminal 6 and ground.
    • If 10 Ω or greater 
    1. Ignition OFF.
    2. Test for less than 2 Ω in the ground circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, repair the open/high resistance in the ground connection.
    • If less than 10 Ω 
  3. Ignition ON.
  4. Verify the scan tool Interior/Courtesy Lighting Master Switch parameter is Door.
    • If Cancel 
    1. Ignition OFF, disconnect the X7 harness connector at the K9 Body Control Module.
    2. Test for infinite resistance between the signal circuit terminal 4 and ground.
      • If less than infinite resistance, repair the short to ground on the circuit.
      • If infinite resistance, replace the K9 Body Control Module.
    • If On 
    1. Ignition OFF, disconnect the X7 harness connector at the K9 Body Control Module.
    2. Test for infinite resistance between the signal circuit terminal 5 and ground.
      • If less than infinite resistance, repair the short to ground on the circuit.
      • If infinite resistance, replace the K9 Body Control Module.
    • If Door 
  5. Install a 3 A fused jumper wire between the signal circuit terminal 4 and ground.
  6. Verify the scan tool Interior/Courtesy Lighting Master Switch parameter is Cancel.
    • If not Cancel 
    1. Ignition OFF, disconnect the X7 harness connector at the K9 Body Control Module, ignition ON.
    2. Test for less than 1 V between the signal circuit terminal 4 and ground.
      • If 1 V or greater, repair the short to voltage on the circuit.
      • If less than 1 V
    3. Test for less than 2 Ω in the signal circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, replace the K9 Body Control Module.
    • If Cancel 
  7. Install a 3 A fused jumper wire between the signal circuit terminal 5 and ground.
  8. Verify the scan tool Interior/Courtesy Lighting Master Switch parameter is On.
    • If not On 
    1. Ignition OFF, disconnect the X7 harness connector at the K9 Body Control Module, ignition ON.
    2. Test for less than 1 V between the signal circuit terminal 5 and ground.
      • If 1 V or greater, repair the short to voltage on the circuit.
      • If less than 1 V
    3. Test for less than 2 Ω in the signal circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, replace the K9 Body Control Module.
    • If On 
  9. Test or replace the E37A Dome/Reading Lamps.

Dome Lamp Malfunction

  1. Ignition OFF, all doors closed, all accessories OFF, disconnect the harness connector at the E37A Dome/Reading Lamps and E36AH Dome Lamp. It may take up to 2 min for all vehicle systems to power down.
  2. Test for less than 15 Ω between the appropriate ground circuit terminal listed below and ground.
    • E37A Dome/Reading Lamps terminal 6
    • E36AH Dome Lamp - terminal 2
    • If 15 Ω or greater 
    1. Ignition OFF.
    2. Test for less than 2 Ω in the ground circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, repair the open/high resistance in the ground connection.
    • If less than 15 Ω 
  3. Connect a test lamp between the appropriate control circuit terminal listed below and ground, ignition ON.
    • E37A Dome/Reading Lamps terminal 2
    • E36AH Dome Lamp - terminal 3
  4. Verify the test lamp turns ON and OFF when commanding the Courtesy Lamps ON and OFF with a scan tool.
    • If the test lamp is always OFF 
    1. Ignition OFF, disconnect the X7 harness connector at the K9 Body Control Module.
    2. Test for infinite resistance between the control circuit and ground.
      • If less than infinite resistance, repair the short to ground on the circuit.
      • If infinite resistance
    3. Test for less than 2 Ω in the control circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, replace the K9 Body Control Module.
    • If the test lamp is always ON 
    1. Ignition OFF, disconnect the X7 harness connector at the K9 Body Control Module, ignition ON.
    2. Test for less than 1 V between the control circuit terminal and ground.
      • If 1 V or greater, repair the short to voltage on the circuit.
      • If less than 1 V, replace the K9 Body Control Module.
    • If the test lamp turns ON and OFF 
  5. Test or replace the inoperative dome/reading lamp.
scientia non olet · About LEMON Manuals