LEMON Manuals: Even more car manuals for everyone
Home >> Chevrolet >> 2015 >> Cruze LT, Automatic Trans >> Repair and Diagnosis >> External Pages >> Different car >> Section 51 (Lighting System) >> Diagnostic Information and Procedures >> DTC C0277 or C0890: Brake Pedal Position Sensor >> Circuit/System Testing

Circuit/System Testing

WARNING: This page is about a different car, the 2015 Chevrolet Trax and 2015 Buick Encore. However, it is still accessible from the selected car via links, so may be relevant.

DTC C0277 06, C0277 07, C0890 03, and C0890 07

  1. Ignition OFF, disconnect the harness connector at the B22 Brake Pedal Position Sensor, ignition ON.
  2. Verify a test lamp illuminates between the appropriate low reference circuit terminal listed below and B+.
    • Terminal 2 - with MH8/MHB (Trax)
    • Terminal A - with M4P/MR5 (Trax)
    • Terminal 2 (Encore)
    • If the test lamp does not illuminate 
    1. Ignition OFF, disconnect the X1 harness connector at the K9 Body Control Module.
    2. Test for less than 2 Ω in the low reference circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, replace the K9 Body Control Module.
    • If the test lamp illuminates 
  3. Ignition ON.
  4. Test for 4.8-5.2 V between the appropriate 5 V reference circuit terminal listed below and ground.
    • Terminal 1 - with MH8/MHB (Trax)
    • Terminal C - with M4P/MR5 (Trax)
    • Terminal 1 (Encore)
    • If less than 4.8 V 
    1. Ignition OFF, disconnect the X2 harness connector at the K9 Body Control Module.
    2. Test for infinite resistance between the 5 V reference circuit and ground.
      • If less than infinite resistance, repair the short to ground on the circuit.
      • If infinite resistance
    3. Test for less than 2 Ω in the 5 V reference circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, replace the K9 Body Control Module.
    • If greater than 5.2 V 
    1. Ignition OFF, disconnect the X2 harness connector at the K9 Body Control Module, ignition ON.
    2. Test for less than 1 V between the 5 V reference circuit and ground.
      • If 1 V or greater, repair the short to voltage on the circuit.
      • If less than 1 V, replace the K9 Body Control Module.
    • If between 4.8-5.2 V 
  5. Verify the scan tool Brake Pedal Applied parameter is Inactive.
    • If not Inactive 
    1. Ignition OFF, disconnect the X2 harness connector at the K9 Body Control Module, ignition ON.
    2. Test for less than 1 V between the appropriate signal circuit terminal listed below and ground.
      • Terminal 3 - with MH8/MHB (Trax)
      • Terminal B - with M4P/MR5 (Trax)
      • Terminal 3 (Encore)
      • If 1 V or greater, repair the short to voltage on the circuit.
      • If less than 1 V, replace the K9 Body Control Module.
    • If Inactive 
  6. Install a 3 A fused jumper wire between the appropriate 5 V reference and signal circuit terminals listed below.
    • 5 V reference terminal 1 and signal terminal 3 - with MH8/MHB (Trax)
    • 5 V reference terminal C and signal terminal B - with M4P/MR5 (Trax)
    • 5 V reference terminal 1 and signal terminal 3 (Encore)
  7. Verify the scan tool Brake Pedal Applied parameter is Active.
    • If not Active 
    1. Ignition OFF, disconnect the X2 harness connector at the K9 Body Control Module.
    2. Test for infinite resistance between the signal circuit and ground.
      • If less than infinite resistance, repair the short to ground on the circuit.
      • If infinite resistance
    3. Test for less than 2 Ω in the signal circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, replace the K9 Body Control Module.
    • If Active 
  8. Test or replace the B22 Brake Pedal Position Sensor.

DTC C0277 4B

  1. Verify DTC C0277 4B is not set.
    • If DTC C0277 4B is set 
    1. Ignition ON
    2. Perform the BPP sensor recalibration procedure for the K9 Body Control Module. Refer to Brake Pedal Position Sensor Calibration .
    3. Verify the DTC does not reset while operating the vehicle under the conditions for running the DTC.
      • If the DTC resets, replace the B22 Brake Pedal Position Sensor.
      • If the DTC does not reset
    4. All OK.
    • If DTC C0277 4B is not set 
  2. All OK.

DTC C0277 09

  1. Verify DTC C0277 09 is not set.
    • If DTC C0277 09 is set 
    1. Replace the B22 Brake Pedal Position Sensor.
    2. Perform the BPP sensor recalibration procedure for the K9 Body Control Module. Refer to Brake Pedal Position Sensor Calibration .
    3. Verify the DTC does not reset while operating the vehicle under the conditions for running the DTC.
      • If the DTC resets, replace the K9 Body Control Module.
      • If the DTC does not reset
    4. All OK.
    • If DTC C0277 09 is not set 
  2. All OK.
scientia non olet · About LEMON Manuals