LEMON Manuals: Even more car manuals for everyone
Home >> Chevrolet >> 2015 >> Cruze LT, Automatic Trans >> Repair and Diagnosis >> External Pages >> Different car >> Section 51 (Lighting System) >> Diagnostic Information and Procedures >> DTC B2575 or B2699: Headlamps >> Circuit/System Testing

Circuit/System Testing

WARNING: This page is about a different car, the 2015 Chevrolet Trax and 2015 Buick Encore. However, it is still accessible from the selected car via links, so may be relevant.

DTC B2575

  1. Ignition OFF, disconnect the X1 harness connector at the K9 Body Control Module, ignition ON.
  2. Verify a test lamp illuminates between the B+ circuit terminal 2 and ground.
    • If the test lamp does not illuminate and the circuit fuse is good 
    1. Ignition OFF.
    2. Test for less than 2 Ω in the B+ circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, verify the fuse is not open and there is voltage at the fuse.
    • If the test lamp does not illuminate and the circuit fuse is open 
    1. Ignition OFF.
    2. Test for infinite resistance between the B+ circuit and ground.
      • If less than infinite resistance, repair the short to ground on the circuit.
      • If infinite resistance, replace the K9 Body Control Module.
    • If the test lamp illuminates 
  3. Ignition OFF, connect the X1 harness connector at the K9 Body Control Module.
  4. Ignition OFF, exterior lamps OFF, remove the E4G Headlamp - Left Low Beam at the E13LA Headlamp Assembly - Left.
  5. Test for less than 5 Ω between the ground circuit at the socket terminal and ground.
    • If 5 Ω or greater 
    1. Ignition OFF.
    2. Test for less than 2 Ω in the ground circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, repair the open/high resistance in the ground connection.
    • If less than 5 Ω 
  6. Connect a test lamp between the control circuit at the socket terminal and ground, ignition ON.
  7. Verify the test lamp turns ON and OFF when commanding the Left Low Beam/Daytime Running Lamp ON and OFF with a scan tool.
    • If the test lamp is always OFF 
    1. Ignition OFF, disconnect the X4 harness connector at the K9 Body Control Module.
    2. Test for infinite resistance between the control circuit and ground.
      • If less than infinite resistance, repair the short to ground on the circuit.
      • If infinite resistance
    3. Test for less than 2 Ω in the control circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, replace the K9 Body Control Module.
    • If the test lamp is always ON 
    1. Ignition OFF, disconnect the X4 harness connector at the K9 Body Control Module, ignition ON.
    2. Test for less than 1 V between the control circuit terminal and ground.
      • If 1 V or greater, repair the short to voltage on the circuit.
      • If less than 1 V, replace the K9 Body Control Module.
    • If the test lamp turns ON and OFF 
  8. Test or replace the E4G Headlamp - Left Low Beam bulb.

DTC B2699

  1. Ignition OFF, disconnect the X1 harness connector at the K9 Body Control Module, ignition ON.
  2. Verify a test lamp illuminates between the B+ circuit terminal 3 and ground.
    • If the test lamp does not illuminate and the circuit fuse is good 
    1. Ignition OFF.
    2. Test for less than 2 Ω in the B+ circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, verify the fuse is not open and there is voltage at the fuse.
    • If the test lamp does not illuminate and the circuit fuse is open 
    1. Ignition OFF.
    2. Test for infinite resistance between the B+ circuit and ground.
      • If less than infinite resistance, repair the short to ground on the circuit.
      • If infinite resistance, replace the K9 Body Control Module.
    • If the test lamp illuminates 
  3. Ignition OFF, connect the X1 harness connector at the K9 Body Control Module.
  4. Ignition OFF, exterior lamps OFF, remove the E4H Headlamp - Right Low Beam at the E13RA Headlamp Assembly - Right.
  5. Test for less than 5 Ω between the ground circuit at the socket terminal and ground.
    • If 5 Ω or greater 
    1. Ignition OFF.
    2. Test for less than 2 Ω in the ground circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, repair the open/high resistance in the ground connection.
    • If less than 5 Ω 
  6. Connect a test lamp between the control circuit at the socket terminal and ground, ignition ON.
  7. Verify the test lamp turns ON and OFF when commanding the Right Low Beam/Daytime Running Lamp ON and OFF with a scan tool.
    • If the test lamp is always OFF 
    1. Ignition OFF, disconnect the X4 harness connector at the K9 Body Control Module.
    2. Test for infinite resistance between the control circuit and ground.
      • If less than infinite resistance, repair the short to ground on the circuit.
      • If infinite resistance
    3. Test for less than 2 Ω in the control circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, replace the K9 Body Control Module.
    • If the test lamp is always ON 
    1. Ignition OFF, disconnect the X4 harness connector at the K9 Body Control Module, ignition ON.
    2. Test for less than 1 V between the control circuit terminal and ground.
      • If 1 V or greater, repair the short to voltage on the circuit.
      • If less than 1 V, replace the K9 Body Control Module.
    • If the test lamp turns ON and OFF 
  8. Test or replace the E4H Headlamp - Right Low Beam bulb.
scientia non olet · About LEMON Manuals