LEMON Manuals: Even more car manuals for everyone
Home >> Chevrolet >> 2015 >> Cruze LT, Automatic Trans >> Repair and Diagnosis >> External Pages >> Different car >> Section 36 (Fixed And MOVEABLE Window System) >> Diagnostic Information and Procedures >> DTC B316B, B317A, B318A, or B319A: Driver Window Switch (AXG, A33, A66) >> Circuit/System Testing

Circuit/System Testing

WARNING: This page is about a different car, the 2015 Chevrolet Trax and 2015 Buick Encore. However, it is still accessible from the selected car via links, so may be relevant.
  1. Ignition OFF and all vehicle systems OFF, disconnect the harness connector at the S79D Window Switch-Driver. It may take up to 2 minutes for all vehicle systems to power down.
  2. Test for less than 10 Ω between the ground circuit terminal 11 and ground.
    • If 10 Ω or greater 
    1. Ignition OFF.
    2. Test for less than 2 Ω in the ground circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, repair the open/high resistance in the ground connection.
    • If less than 10 Ω 
  3. Ignition ON.
  4. Verify the scan tool Driver Window Main Control Down Switch parameter is Inactive.
    • If not Inactive 
    1. Ignition OFF, disconnect the harness connector at the M74D Window Motor-Driver.
    2. Test for infinite resistance between the S79D Window Switch-Driver signal circuit terminal 8 and ground.
      • If less than infinite resistance, repair the short to ground on the circuit.
      • If infinite resistance, replace the M74D Window Motor-Driver.
    • If Inactive 
  5. Install a 3 A fused jumper wire between the signal circuit terminal 8 and the ground circuit terminal 11.
  6. Verify the scan tool Driver Window Main Control Down Switch parameter is Active
    • If not Active 
    1. Ignition OFF, remove the 3 A fused jumper wire, disconnect the harness connector at the M74D Window Motor-Driver, ignition ON.
    2. Test for less than 1 V between the S79D Window Switch-Driver signal circuit terminal 8 and ground.
      • If 1 V or greater, repair the short to voltage on the circuit.
      • If less than 1 V
    3. Test for less than 2 Ω in the signal circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, replace the M74D Window Motor-Driver.
    • If Active 
  7. Verify the scan tool Driver Window Main Control Up Switch parameter is Inactive.
    • If not Inactive 
    1. Ignition OFF, disconnect the harness connector at the M74D Window Motor-Driver.
    2. Test for infinite resistance between the S79D Window Switch-Driver signal circuit terminal 9 and ground.
      • If less than infinite resistance, repair the short to ground on the circuit.
      • If infinite resistance, replace the M74D Window Motor-Driver.
    • If Inactive 
  8. Install a 3 A fused jumper wire between the signal circuit terminal 9 and the ground circuit terminal 11.
  9. Verify the scan tool Driver Window Main Control Up Switch parameter is Active
    • If not Active 
    1. Ignition OFF, remove the 3 A fused jumper wire, disconnect the harness connector at the M74D Window Motor-Driver, ignition ON.
    2. Test for less than 1 V between the S79D Window Switch-Driver signal circuit 9 and ground.
      • If 1 V or greater, repair the short to voltage on the circuit.
      • If less than 1 V
    3. Test for less than 2 Ω in the signal circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, replace the M74D Window Motor-Driver.
    • If Active 
  10. Verify the scan tool Driver Window Main Control Express Switch parameter is Inactive.
    • If not Inactive 
    1. Ignition OFF, disconnect the harness connector at the M74D Window Motor-Driver.
    2. Test for infinite resistance between the S79D Window Switch-Driver signal circuit terminal 10 and ground.
      • If less than infinite resistance, repair the short to ground on the circuit.
      • If infinite resistance, replace the M74D Window Motor-Driver.
    • If Inactive 
  11. Install a 3 A fused jumper wire between the signal circuit terminal 10 and the ground circuit terminal 11.
  12. Verify the scan tool Driver Window Main Control Express Switch parameter is Active
    • If not Active 
    1. Ignition OFF, remove the 3 A fused jumper wire, disconnect the harness connector at the M74D Window Motor-Driver, ignition ON.
    2. Test for less than 1 V between the S79D Window Switch-Driver signal circuit 10 and ground.
      • If 1 V or greater, repair the short to voltage on the circuit.
      • If less than 1 V
    3. Test for less than 2 Ω in the signal circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, replace the M74D Window Motor-Driver.
    • If Active 
  13. Test or replace the S79D Window Switch-Driver.
scientia non olet · About LEMON Manuals