LEMON Manuals: Even more car manuals for everyone
Home >> Chevrolet >> 2015 >> Cruze LT, Automatic Trans >> Repair and Diagnosis >> Engine Performance >> Testing & Diagnosis >> Engine Controls And Fuel - 1.4L (LUJ, LUV) - DTC P0010 To P0246 >> Diagnostic Information and Procedures >> DTC P0112, P0113 or P0114: Intake Air Temperature (IAT) Sensor Circuit >> Circuit/System Testing

Circuit/System Testing

NOTE: You must perform the Circuit/System Verification  before proceeding with Circuit/System Testing.
  1. Ignition OFF and all vehicle systems OFF, it may take up to 2 min. for all vehicle systems to power down. Disconnect the harness connector at the B75C Multifunction Intake Air sensor.
  2. Test for less than 2 Ω between the low reference circuit terminal 7 and ground.
    • If 2 Ω or greater 
    1. Ignition OFF, disconnect the harness connector at the K20 Engine Control Module.
    2. Test for less than 2 Ω in the low reference circuit end to end.
      • If 2 Ω or greater, repair the open or high resistance in the circuit.
      • If less than 2 Ω replace the K20 Engine Control Module.
    • If less than 2 Ω 
  3. Ignition ON, test for 4.8-5.2 V between signal circuit terminal 8 and ground.
    • If less than 4.8 V 
    1. Ignition OFF, disconnect the harness connector at the K20 Engine Control Module.
    2. Test for infinite resistance between the signal circuit and ground.
      • If less than infinite resistance, repair the short to ground on the circuit.
      • If infinite resistance
    3. Test for less than 2 Ω in the signal circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, replace the K20 Engine Control Module.
    • If greater than 5.2 V 
    1. Ignition OFF, disconnect the harness connector at the K20 Engine Control Module.
      NOTE: If the signal circuit is shorted to a voltage the engine control module or the sensor may be damaged.
    2. Ignition ON, test for less than 1 V between the signal circuit and ground.
      • If 1 V or greater, repair the short to voltage on the circuit.
      • If less than 1 V, replace the K20 Engine Control Module.
    • If between 4.8-5.2 V 
  4. Ignition ON, verify the scan tool IAT Sensor 1 parameter is colder than -39°C (-38°F).
    • If warmer than -39°C (-38°F). 
    1. Ignition OFF, disconnect the harness connector at the K20 Engine Control Module.
    2. Test for infinite resistance between the signal circuit terminal 8 and ground.
      • If less than infinite resistance, repair the short to ground on the circuit.
      • If infinite resistance
    3. Test for less than 2 Ω in the signal circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, replace the K20 Engine Control Module.
    • If colder than -39°C (-38°F). 
  5. Ignition OFF, install a 3 A fused jumper wire between the signal circuit terminal 8 and the low reference circuit terminal 7.
  6. Verify the scan tool IAT Sensor 1 parameter is warmer than 148°C (298°F).
    • If colder than 148°C (298°F). 
    1. Ignition OFF, remove the jumper wire, disconnect the harness connector at the K20 Engine Control Module, ignition ON.
    2. Test for less than 1 V between the signal circuit and ground.
      • If 1 V or greater, repair the short to voltage on the circuit.
      • If less than 1 V
    3. Ignition OFF.
    4. Test for less than 2 Ω in the signal circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, replace the K20 Engine Control Module.
    • If warmer than 148°C (298°F). 
  7. Test or replace the B75C Multifunction Intake Air sensor.
scientia non olet · About LEMON Manuals