LEMON Manuals: Even more car manuals for everyone
Home >> Chevrolet >> 2012 >> Cruze Eco, Automatic Trans >> Repair and Diagnosis >> External Pages >> Different car >> Section 89 (Engine Mechanical - 2.0L) >> Repair Instructions - Off Vehicle >> Cylinder Sleeve Installation >> Special Tools >> Cylinder Sleeve Trimming

Cylinder Sleeve Trimming

WARNING: This page is about a different car, the 2010 Chevrolet Cobalt. However, it is still accessible from the selected car via links, so may be relevant.
Fig 1: Cylinder Liner Trimming Tools View (1 Of 2)
GM1253966Courtesy of GENERAL MOTORS CORP.

The EN 45680-861 trim tool assembly (2) from EN 45680-850:  kit contains or requires the following components to complete 86 mm cylinder sleeve trimming:

Fig 2: Cylinder Liner Trimming Tools View (2 Of 2)
GM1253969Courtesy of GENERAL MOTORS CORP.
    CAUTION: Do not bore or hone the cylinder bore sleeve. The cylinder bore sleeve inside diameter (I.D) is fully machined and honed to size and is optimally finished as shipped. Any attempt to modify this factory-produced sizing and finish with additional boring and honing will lead to engine damage, excessive noise or abnormal oil consumption.
    Fig 3: Placing Metal Shaving Catch Plug Into Cylinder Bore Sleeve
    GM1253974Courtesy of GENERAL MOTORS CORP.
  1. After installing the NEW cylinder bore sleeve(s) into the engine block, trim the excess material from the cylinder bore sleeve flange.
    2. CAUTION: Ensure that all the metal particles are collected in order to prevent internal damage to the engine or bearings.
  2. Place the metal shaving catch plug EN 45680-863 into the cylinder bore sleeve to be trimmed. Position the top approximately 3.0 mm (0.12 in) below the top surface of the cylinder bore sleeve.
  3. Place an additional metal shaving catch plug EN 45680-863 into all remaining cylinder bore sleeves.
    4. Fig 4: Identifying Catch Plug Positioning
    GM1253978Courtesy of GENERAL MOTORS CORP.
    CAUTION: Installing the metal shaving catch plug deeper than the recommended depth will create a decrease in vacuum system performance. A decrease in vacuum system performance will cause metal shavings to enter the engine and cause engine failure.
    CAUTION: Installing the metal shaving catch plug above the recommended depth will cause damage to the metal shaving catch plug.
  4. Ensure that the metal shaving catch plug EN 45680-863 is 3.0 mm (0.12 in) below the top surface of the cylinder bore sleeve.
  5. Ensure that the correct bore trimmer pilot and cutter bit are installed on the trimmer base assembly EN 45680-861:
    • EN 45680-869 cutter bit and screw
    • EN 45680-899 trimmer pilot, 86 mm sleeve
    6. Fig 5: Identifying Set Gauge Ring Groove
    GM1253982Courtesy of GENERAL MOTORS CORP.
    NOTE: Before using the trim tool assembly, the height of the cutting blades must be set to the proper specification. The proper specification is that the cylinder bore sleeve flange must be flush to +0.02 mm (0.0008 in) above the block deck surface.
  6. The groove side of the set gauge ring (1) on the gauge ring assembly EN 45680-862 should be positioned upward on a flat surface.
    7. Fig 6: View Of Trim Tool Assembly Components And Positioning
    GM1253983Courtesy of GENERAL MOTORS CORP.
    NOTE: Ensure that the set gauge ring surfaces are clean.
  7. Carefully position the trim tool assembly EN 45680-861 onto the set gauge ring.
  8. Loosen the shaft collar screw (2).
  9. Push the shaft collar (2) downward using the trim tool preloader (1) on the gauge ring assembly EN 45680-862 until the shaft collar is positioned against the top of the flange bearing (3).
    10. NOTE: Once this procedure is done, it is not necessary to reset the trim tool assembly height until the blades are worn, damaged, or replaced.
  10. Apply downward pressure on the collar and inner drive shaft using the trim tool preloader (1), then tighten the shaft collar screw to 19 N.m (14 lb ft).
    11. Fig 7: Aligning Trim Tool Assembly
    GM1253992Courtesy of GENERAL MOTORS CORP.
  11. Place the trim tool assembly EN 45680-861 onto the cylinder to be trimmed with the directional arrow (1) pointing in line with the crankshaft centerline and the front of the block.
  12. Install the 4 bolts EN 45680-864 (2) into the cylinder head bolt holes in the block. Tighten the bolts to 20 N.m (15 lb ft).
    13. Fig 8: View Of Drive Adapter
    GM1253994Courtesy of GENERAL MOTORS CORP.
    CAUTION: For proper tool operation, a drill motor with a 1/2 inch chuck, 1 1/8 hp, 7 amps, triple gear reduction, and a 450-600 RPM rotational speed in a clockwise direction must be used. If the proper drill motor is not used, damage to the cylinder bore sleeve will occur.
  13. Fasten the drive adapter EN 45680-866 (1) into the drill chuck.
    14. CAUTION: Ensure that there are no crimps in the air feed hose or the vacuum hose. Crimps in the hose may cause metal shavings to exit the cutting tool in any direction, causing engine damage.
  14. Connect a compressed air supply 517.10-861.84 kPa (75-125 psi) to the male quick connect (3) located on trim tool assembly EN 45680-861. Turn the compressed air valve (2) to the open position. This starts the venturi vacuum system that will catch the metal shavings.
    15. NOTE: It should not take longer than 15 seconds to complete the trimming procedure. If it does, the trimming bits must be repositioned to a new cutting surface.
  15. Place the drive adapter EN 45680-866 and drill assembly (1) vertically onto the drive adapter end of trim tool assembly EN 45680-861. Do not apply downward force on the drill until full rotational speed has been reached. After reaching full rotational speed, apply firm downward force until the cutting action is complete.
  16. Remove the drive adapter EN 45680-866 (1) and drill assembly from the trim tool assembly EN 45680-861.
  17. Turn off the compressed air valve (2).
  18. Remove the trim tool assembly EN 45680-861 from the engine block.
  19. Remove any material shavings that may be found on the metal shaving catch plug EN 45680-863.
  20. Wipe the cylinder bore sleeve and surrounding areas free of any powder residue and then remove the metal shaving catch plug EN 45680-863.
    21. Fig 9: Checking Cylinder Block Deck Surface With Straight Edge
    GM1415604Courtesy of GENERAL MOTORS CORP.
  21. Install a straight edge on the cylinder block perpendicular to the crankshaft center line.
  22. Using a light, illuminate the backside of the straight edge.
    23. Fig 10: View Of Improperly Cut Cylinder Bore Sleeve
    GM1415606Courtesy of GENERAL MOTORS CORP.
  23. Looking at the front of the straight edge, check to see if light is protruding through the bottom of the straight edge and the top of the cylinder bore sleeve flange. If light is present on either side or both sides of the cylinder bore sleeve, the cylinder bore sleeve is cut incorrectly and a new cylinder bore sleeve needs to be installed.
    24. Fig 11: View Of For Properly Cut Cylinder Bore Sleeve
    GM1415607Courtesy of GENERAL MOTORS CORP.
  24. Looking at the front of the straight edge, check to see if light is protruding through the bottom of the straight edge and the top of the cylinder block deck surface. If light is present on both sides of the cylinder block, the cylinder bore sleeve is cut correctly.
  25. Proceed to the next bore sleeve to be trimmed repeating steps 10-23 if necessary.
scientia non olet · About LEMON Manuals