LEMON Manuals: Even more car manuals for everyone
Home >> Chevrolet >> 2012 >> Cruze Eco, Automatic Trans >> Repair and Diagnosis >> External Pages >> Different car >> Section 105 (Automatic Transmission - 4T45-E - Repair Instructions - On Vehicle) >> Repair Instructions - On Vehicle >> Transmission Replacement >> Installation Procedure

Installation Procedure

WARNING: This page is about a different car, the 2010 Pontiac G5 and 2010 Chevrolet Cobalt. However, it is still accessible from the selected car via links, so may be relevant.
  1. Install the PNP switch.
  2. Install the shifter cable bracket.
  3. Install the lower transmission to engine stud.
  4. Install the transmission mount.
    5. Fig 1: View Of Lower Transmission To Engine Stud
    GM104581Courtesy of GENERAL MOTORS CORP.
  5. Position the transaxle in the vehicle.
    6. Fig 2: Identifying Lower Transmission To Engine Bolts And Stud
    GM104580Courtesy of GENERAL MOTORS CORP.
    CAUTION: Refer to Fastener Caution .
  6. Install the lower transmission to engine bolts and nuts and tighten to 90 N.m (66 lb ft).
  7. Connect the transaxle cooler pipes to the transaxle and tighten the cooler pipes to 8 N.m (71 lb in).
  8. Use the J 43653  to prevent the crankshaft from rotating.
    9. Fig 3: View Of Flywheel To Torque Converter Bolts
    GM475919Courtesy of GENERAL MOTORS CORP.
  9. Install the torque converter to flywheel bolts and tighten to 62 N.m (46 lb ft).
  10. Install the wheel drive shafts to the transaxle. Refer to Wheel Drive Shaft Replacement .
  11. Remove the transaxle jack.
    12. Fig 4: View Of VSS Wiring Harness
    GM414901Courtesy of GENERAL MOTORS CORP.
  12. Connect the wiring harness to the VSS.
    13. Fig 5: View Of Flywheel Inspection Cover Bolts
    GM510441Courtesy of GENERAL MOTORS CORP.
  13. Install the starter. Refer to Starter Replacement .
  14. Install the flywheel inspection cover bolts and tighten to 10 N.m (89 lb in).
    15. Fig 6: Identifying Lower Transmission To Engine Bolts And Stud
    GM104580Courtesy of GENERAL MOTORS CORP.
  15. Install the upper transmission to engine bolts and stud and tighten all of the bolts to 90 N.m (66 lb ft).
    16. Fig 7: Identifying Transmission-To-Engine Brace Bolts
    GM510437Courtesy of GENERAL MOTORS CORP.
  16. Install the transmission to engine brace bolts and tighten to 72 N.m (53 lb ft).
  17. Install the frame. Refer to Frame Replacement .
  18. Lower the vehicle.
  19. Install the transaxle mount to body bolts and tighten to 90 N.m (66 lb ft).
  20. Remove the engine support fixture.
  21. Install the engine wiring harness grounds to the transaxle to engine mount stud and nut and tighten the nut to 8 N.m (71 lb in).
    22. Fig 8: View Of Shift Cable & Shift Linkage
    GM494775Courtesy of GENERAL MOTORS CORP.
  22. Install the shift linkage to the transmission.
    23. Fig 9: Locating Transaxle & PNP Switch Connectors
    GM414408Courtesy of GENERAL MOTORS CORP.
  23. Connect the electrical connectors to the PNP switch and transaxle.
  24. Install the underhood electrical junction block. Refer to Underhood Electrical Center or Junction Block Bracket Replacement .
  25. Install the TCM. Refer to Transmission Control Module Replacement .
  26. Install the ECM. Refer to Engine Control Module Replacement for the 2.2L or 2.4L engine.
  27. Install the air outlet duct, the PCV hose, and the intake plenum. Refer to Air Cleaner Assembly Replacement for the 2.2L or 2.4L engine.
  28. Connect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection .
  29. Inspect the transmission fluid level.
    30. NOTE: It is recommended that transmission adaptive pressure (TAP) information be reset.
    Resetting the TAP values using a scan tool will erase all learned values in all cells. As a result, the ECM, powertrain control module (PCM), or TCM will need to relearn TAP values. Transmission performance may be affected as new TAP values are learned.
  30. Reset the TAP values. Refer to Transmission Adaptive Functions .
scientia non olet · About LEMON Manuals