LEMON Manuals: Even more car manuals for everyone
Home >> Chevrolet >> 2012 >> Corvette Z06 >> Repair and Diagnosis >> External Pages >> Different car >> Section 142 (Anti-Lock Brake System - Non-Hybrid Less Than 3900 Kg (8600 Lb) GVW With TCS & VSES) >> Diagnostic Information and Procedures >> DTC C0035-C0050 >> Circuit/System Testing

Circuit/System Testing

WARNING: This page does not describe the selected car, but rather 8 other vehicles, including the 2008 GMC Yukon XL, 2008 GMC Yukon, 2008 Chevrolet Tahoe, 2008 Chevrolet Suburban, and 2008 Chevrolet Avalanche. However, it is still accessible from the selected car via links, so may be relevant.
  1. Ignition OFF, disconnect the harness connector at the EBCM.
  2. Ignition ON, test for less than 1 volt between the 12-volt reference circuit terminal of the appropriate sensor listed below and ground.
    • LF Sensor circuit terminal 21
    • RF Sensor circuit terminal 18
    • LR Sensor circuit terminal 33
    • RR Sensor circuit terminal 19
    • If greater than the specified range, test the low reference circuit for a short to voltage.
  3. Test for less than 1 volt between the signal circuit terminal of the appropriate sensor listed below and ground.
    • LF Sensor circuit terminal 34
    • RF Sensor circuit terminal 6
    • LR Sensor circuit terminal 20
    • RR Sensor circuit terminal 31
    • If greater than the specified range, test the signal circuit for a short to voltage.
  4. Ignition OFF, test for infinite resistance between the 12-volt reference terminal of the appropriate sensor circuit listed below and ground.
    • LF Sensor circuit terminal 21
    • RF Sensor circuit terminal 18
    • LR Sensor circuit terminal 33
    • RR Sensor circuit terminal 19
    • If less than the specified value, test the 12-volt reference circuit for a short to ground.
  5. Test for infinite resistance between the following signal circuit terminal of the appropriate sensor circuit listed below and ground.
    • LF Sensor circuit terminal 34
    • RF Sensor circuit terminal 6
    • LR Sensor circuit terminal 20
    • RR Sensor circuit terminal 31
    • If less than the specified value, test the signal circuit for a short to ground.
  6. Ignition OFF, disconnect the harness connector at the appropriate WSS.
  7. Test for less than 2 ohms between the appropriate 12-volt reference circuit terminals listed below.
    • LF Sensor circuit terminal 21 at the EBCM harness connector, and terminal 2 at the WSS harness connector
    • RF Sensor circuit terminal 18 at the EBCM harness connector, and terminal 2 at the WSS harness connector
    • LR Sensor circuit terminal 33 at the EBCM harness connector, and terminal B at the WSS harness connector
    • RR Sensor circuit terminal 19 at the EBCM harness connector, and terminal B at the WSS harness connector
    • If greater than the specified range, test the 12-volt reference circuit for an open or high resistance.
  8. Test for less than 2 ohms between the appropriate signal circuit terminals listed below.
    • LF Sensor circuit terminal 34 at the EBCM harness connector, and terminal 1 at the WSS harness connector
    • RF Sensor circuit terminal 6 at the EBCM harness connector, and terminal 1 at the WSS harness connector
    • LR Sensor circuit terminal 20 at the EBCM harness connector, and terminal A at the WSS harness connector
    • RR Sensor circuit terminal 31 at the EBCM harness connector, and terminal A at the WSS harness connector
    • If greater than the specified range, test the signal circuit for an open or high resistance.
  9. If all circuits test normal, replace the appropriate wheel speed sensor. If the DTC resets replace the EBCM.
scientia non olet · About LEMON Manuals