LEMON Manuals: Even more car manuals for everyone
Home >> Chevrolet >> 2011 >> Suburban K2500 >> Repair and Diagnosis >> External Pages >> Different car >> Section 1758 (Engine Mechanical - Hybrid (LZ1) - Repair Instructions - On Vehicle) >> Repair Instructions - On Vehicle >> Cylinder Head Replacement - Right Side >> Installation Procedure

Installation Procedure

WARNING: This page is about a different car, the 2011 GMC Yukon, 2011 Chevrolet Tahoe, and 2011 Cadillac Escalade. However, it is still accessible from the selected car via links, so may be relevant.
    Fig 1: Cylinder Head Bolt Holes And Locating Pins
    GM63235Courtesy of GENERAL MOTORS CORP.
    WARNING:

    Wear safety glasses in order to avoid eye damage.

    CAUTION:

    Clean all dirt, debris, and coolant from the engine block cylinder head bolt holes. Failure to remove all foreign material may result in damaged threads, improperly tightened fasteners or damage to components.

    NOTE:

    If installing a new cylinder head it is necessary to install a new engine coolant air bleed plug into the rear coolant passage of the cylinder head. Refer to Cylinder Head Assemble .

    NOTE:
    • Do not reuse the cylinder head bolts. Install NEW cylinder head bolts during assembly.
    • Do not use any type of sealant on the cylinder head gasket, unless specified.
  1. Clean the engine block cylinder head bolt holes, if required. Thread repair tool J 42385-107, found in J 42385-200 may be used to clean the threads of old threadlocking material.
  2. Spray cleaner GM P/N 12346139, P/N 12377981 (Canadian P/N 10953463), or equivalent into the hole.
  3. Clean the cylinder head bolt holes with compressed air.
  4. Check the cylinder head locating pins for proper installation (a) 8.3 mm (0.327 in).
    5. Fig 2: Cylinder Head Gasket And Locating Pins
    GM1658157Courtesy of GENERAL MOTORS CORP.
    NOTE:

    When properly installed, with FRONT on the right side, the tab on the cylinder head gasket should be located right of center.

  5. Install the NEW cylinder head gasket (217) onto the locating pins.
    6. Fig 3: Cylinder Head And Bolts
    GM1658156Courtesy of GENERAL MOTORS CORP.
  6. Install the cylinder head (218) onto the locating pins.
  7. Install the NEW cylinder head bolts (220, 221).
    8. Fig 4: Cylinder Head Bolt Tightening Sequence
    GM260150Courtesy of GENERAL MOTORS CORP.
    CAUTION:

    Refer to Fastener Caution .

  8. Tighten the cylinder head bolts.
    1. Tighten the M11 cylinder head bolts (1-10) a first pass in sequence to 30 N.m (22 lb ft).
    2. Tighten the M11 cylinder head bolts (1-10) a second pass in sequence to 90 degrees using J 45059 .
    3. Tighten the M11 cylinder head bolts (1-10) a final pass to 70 degrees in sequence using J 45059 .
    4. Tighten the M8 cylinder head bolts (11-15) to 30 N.m (22 lb ft). Begin with the center bolt (11) and alternating side-to-side, work outward tightening all of the bolts.
    9. Fig 5: Right Cylinder Head Engine Harness Studs And Retainers
    GM1970126Courtesy of GENERAL MOTORS CORP.
  9. Position the engine harness to the cylinder head.
  10. Install the engine harness stud (1) to the front of the right cylinder head and tighten the stud to 25 N.m (18 lb ft).
  11. Install the pushrods. Refer to Valve Rocker Arm and Push Rod Replacement .
  12. Install the right exhaust manifold. Refer to Exhaust Manifold Replacement - Right Side .
  13. Install the coolant air bleed pipe. Refer to Engine Coolant Air Bleed Pipe Replacement (with AFM) , Engine Coolant Air Bleed Pipe Replacement (without AFM) .
  14. Install the intake manifold. Refer to Intake Manifold Replacement .
  15. Install the oil level indicator. Refer to Oil Level Indicator Tube Replacement .
  16. Install the drive motor generator control module. Refer to Drive Motor Generator Control Module Assembly Replacement .
scientia non olet · About LEMON Manuals