LEMON Manuals: Even more car manuals for everyone
Home >> Chevrolet >> 2010 >> Traverse LT, AWD >> Repair and Diagnosis >> External Pages >> Different car >> Section 517 (Engine Controls And Fuel - 3.6L (LLT) - DTC P0010 To DTC P0336) >> Diagnostic Information and Procedures >> DTC P0121-P0123, P0222, P0223, P16A0-P16A2, or P2135: Throttle Position Sensor >> Circuit/System Verification

Circuit/System Verification

WARNING: This page is about a different car, the 2016 GMC Acadia, 2016 Chevrolet Traverse, and 2016 Buick Enclave. However, it is still accessible from the selected car via links, so may be relevant.
    NOTE:

    If you were sent here from DTC P0068, P0101, P0106, or P1101 refer to Circuit/System Testing.

  1. Ignition ON.
  2. Verify that DTC P0601-P0606, P06A3, and P16F3 is not set.
    • If a DTC is not set 
  3. Verify the scan tool Throttle Body Idle Airflow Compensation parameter is less than 90 %.
    • If less than 90 % 
  4. Verify that DTC P0122, P0123, P0222, P0223, P16A0, P16A1, P16A2, or P2135 are not set.
    • If DTC P0122, P0123, P0222, P0223, or P2135 are the only DTCs set 

      Replace the Q38 Throttle Body.

    • If DTC P16A0, P16A1, or P16A2 is set with any of the DTCs 

      Refer to Circuit/System Testing.

    • If none of the DTCs are set 
  5. Verify the TP Sensors 1 and 2 Agree/Disagree parameter displays Agree while performing the Throttle Sweep Test with a scan tool.
    • If Agree is not displayed 

      Replace the Q38 Throttle Body.

    • If Agree is displayed 
  6. Verify DTC P0122, P0123, P0222, P0223, P16A0, P16A1, P16A2, and P2135 is not set.
    • If a DTC is set 

      Refer to Circuit/System Testing.

    • If a DTC is not set 
  7. Determine the current vehicle testing altitude.
  8. Verify the scan tool MAP Sensor pressure parameter is within range specified in the Altitude Versus Barometric Pressure table.
    • If the MAP Sensor pressure is not in range 

      Refer to DTC P0106 .

    • If the MAP Sensor pressure is within range 
  9. Engine idling.
  10. Verify the scan tool MAP Sensor pressure parameter is between 26-52 kPa (3.8-7.5 psi) and changes with accelerator pedal input.
    • If not between 26-52 kPa (3.8-7.5 psi) or does not change 

      Refer to DTC P0106 .

    • If between 26-52 kPa (3.8-7.5 psi) and changes 
  11. Verify the scan tool MAF Sensor g/s parameter changes smoothly and gradually as the engine speed is increased and decreased while performing the actions listed below.
    1. Engine idling
    2. Perform the scan tool snapshot function.
    3. Increase the engine speed slowly to 3, 000 RPM and then back to idle.
    4. Exit from the scan tool snapshot and review the data.
    5. Observe the MAF Sensor parameter frame by frame with a scan tool.
    • If the MAF Sensor parameter does not change smoothly and gradually 

      Refer to DTC P0101 .

    • If the MAF Sensor parameter changes smoothly and gradually 
  12. Operate the vehicle within the Conditions for Running the DTC. You may also operate the vehicle within the conditions that you observed from the Freeze Frame/Failure Records data.
  13. Verify the DTC does not set.
    • If the DTC sets 

      Refer to Circuit/System Testing.

    • If the DTC does not set 
  14. All OK.
scientia non olet · About LEMON Manuals