LEMON Manuals: Even more car manuals for everyone
Home >> Chevrolet >> 2010 >> Traverse LT, AWD >> Repair and Diagnosis >> External Pages >> Different car >> Section 479 (Seat Heating System And Seat Cooling System) >> Diagnostic Information and Procedures >> DTC B2425 or B2430: Left/Right Seat Heater Cushion (Without Memory A45) >> Circuit/System Testing

Circuit/System Testing

WARNING: This page is about a different car, the 2016 GMC Acadia, 2016 Chevrolet Traverse, and 2016 Buick Enclave. However, it is still accessible from the selected car via links, so may be relevant.

B2425 0A, B2425 0B, B2425 0C, B2425 0D, B2425 0E, B2425 04, or B2425 1F

  1. Ignition OFF, disconnect the X1 harness connector at the K29 Seat Heating Control Module.
    2. IMPORTANT:

    When measuring the resistance, the resistance values are based on the seat being at room temperature of 20°C (68°F).

  2. Test for 2-10 Ω between the control circuit terminal 3 and control circuit terminal 5.
    • If less than the specified range, test for a short between the control circuits. If the circuits test normal, test or replace the E14B Seat Heating Element - Driver Cushion.
    • If greater than the specified range, test the control circuits for an open/high resistance. If the circuits test normal, test or replace the E14B Seat Heating Element - Driver Cushion.
  3. Ignition OFF, disconnect the X2 and X4 harness connectors at the K29 Seat Heating Control Module.
  4. Test for 3.3 k-300 kΩ between the signal circuit terminal 9 X4 and the low reference circuit terminal 6 X2.
    • If less than the specified range, test for a short between the signal and low reference circuits. If the circuits test normal, test or replace the E14B Seat Heating Element - Driver Cushion.
    • If greater than the specified range, test the signal circuit and low reference circuit for a short to voltage or an open/high resistance. If the circuits test normal, test or replace the E14B Seat Heating Element - Driver Cushion.
  5. Ignition OFF, connect the X1, X2, and X4 harness connectors at the K29 Seat Heating Control Module.
  6. Disconnect the harness connector at the E14B Seat Heating Element - Driver Cushion.
  7. Ignition ON, test for 4.8-5.2 V between the signal circuit terminal 3 and ground.
    • If less than the specified range, test the signal circuit for a short to ground. If the circuit tests normal, replace the K29 Seat Heating Control Module.
    • If greater than the specified range, test the signal circuit for a short to voltage. If the circuit tests normal, replace the K29 Seat Heating Control Module.
  8. If all circuits test normal, replace the K29 Seat Heating Control Module.

B2430 0A, B2430 0B, B2430 0C, B2430 0D, B2430 0E, B2430 04, or B2430 1F

  1. Ignition OFF, disconnect the X1 harness connector at the K29 Seat Heating Control Module.
    2. IMPORTANT:

    When measuring the resistance, the resistance values are based on the seat being at room temperature of 20°C (68°F).

  2. Test for 2-10 Ω between the control circuit terminal 6 and the control circuit terminal 2.
    • If less than the specified range, test for a short between the control circuits. If the circuits test normal, test or replace the E14D Seat Heating Element - Passenger Cushion.
    • If greater than the specified range, test the control circuits for an open/high resistance. If the circuits test normal, test or replace the E14D Seat Heating Element - Passenger Cushion.
  3. Ignition OFF, disconnect the X2 and X4 harness connectors at the K29 Seat Heating Control Module.
  4. Test for 3.3 k-300 kΩ between the signal circuit terminal 20 X4 and the low reference circuit terminal 8 X2.
    • If less than the specified range, test for a short between the signal and low reference circuits. If the circuits test normal, test or replace the E14D Seat Heating Element - Passenger Cushion.
    • If greater than the specified range, test the signal circuit and low reference circuit for a short to voltage or an open/high resistance. If the circuits test normal, test or replace the E14D Seat Heating Element - Passenger Cushion.
  5. Ignition OFF, connect the X1, X2, and X4 harness connectors at the K29 Seat Heating Control Module.
  6. Disconnect the harness connector at the E14D Seat Heating Element - Passenger Cushion.
  7. Ignition ON, test for 4.8-5.2 V between the signal circuit terminal 3 and ground.
    • If less than the specified range, test the signal circuit for a short to ground. If the circuit tests normal, replace the K29 Seat Heating Control Module.
    • If greater than the specified range, test the signal circuit for a short to voltage. If the circuit tests normal, replace the K29 Seat Heating Control Module.
  8. If all circuits test normal, replace the K29 Seat Heating Control Module.
scientia non olet · About LEMON Manuals