LEMON Manuals: Even more car manuals for everyone
Home >> Chevrolet >> 2010 >> Traverse LT, AWD >> Repair and Diagnosis >> External Pages >> Different car >> Section 479 (Seat Heating System And Seat Cooling System) >> Diagnostic Information and Procedures >> DTC B2425 or B2430: Left/Right Seat Heater Cushion (Dealer Installed) >> Circuit/System Testing

Circuit/System Testing

WARNING: This page is about a different car, the 2016 GMC Acadia, 2016 Chevrolet Traverse, and 2016 Buick Enclave. However, it is still accessible from the selected car via links, so may be relevant.

B2425 0A, B2425 0B, B2425 0C, B2425 0D, B2425 0E, B2425 04, or B2425 1F

  1. Ignition OFF, disconnect the X1 harness connector at the K29 Seat Heating Control Module.
    2. IMPORTANT:

    Element resistance must be measured twice to ensure that all failure conditions are simulated. First with the seat unoccupied, then with the seat occupied.

  2. Test for 2.0 - 8.0 Ω between control circuit terminal 3 and control circuit terminal 5.
    • If less than the specified range, test for a short between the control circuits. If the circuits test normal, replace the E14B Seat Heating Element - Driver Cushion.
    • If greater than the specified range, test the control circuits for an open/high resistance. If the circuits test normal replace the E14B Seat Heating Element - Driver Cushion.
  3. Disconnect the X2 and X4 harness connectors at the K29 Seat Heating Control Module.
  4. Test for 850 Ω - 300 kΩ between the signal circuit terminal 9 X4 and the low reference circuit terminal 6 X2.
    • If less than the specified range, test for a short between the signal and low reference circuits. If the circuits test normal, replace the E14B Seat Heating Element - Driver Cushion.
    • If greater than the specified range, test the signal and low reference circuits for a short to voltage or an open/high resistance. If the circuits test normal, replace the E14B Seat Heating Element - Driver Cushion.
  5. Connect the X1, X2 and X4 harness connectors at the K29 Seat Heating Control Module.
  6. Disconnect the harness connector at the E14B Seat Heating Element - Driver Cushion.
  7. Ignition ON, test for 4.8 - 5.2 V between the signal circuit terminal C and ground.
    • If greater than the specified range, test the signal circuit for a short to voltage. If the circuit tests normal, replace the K29 Seat Heating Control Module.
    • If less than the specified range, test the signal circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the K29 Seat Heating Control Module.
  8. If all circuits test normal, replace the K29 Seat Heating Control Module.

B2430 0A, B2430 0B, B2430 0C, B2430 0D, B2430 0E, B2430 04, or B2430 1F

  1. Ignition OFF, disconnect the X1 harness connector at the K29 Seat Heating Control Module.
    2. IMPORTANT:

    Element resistance must be measured twice to ensure that all failure conditions are simulated. First with the seat unoccupied, then with the seat occupied.

  2. Test for 2.0 - 8.0 Ω between control circuit terminal 6 and control circuit terminal 2.
    • If less than the specified range, test for a short between the control circuits. If the circuits test normal, replace the E14D Seat Heating Element - Passenger Cushion.
    • If greater than the specified range, test the control circuits for an open/high resistance. If the circuits test normal, replace the E14D Seat Heating Element - Passenger Cushion.
  3. Disconnect the X2 and X4 harness connectors at the K29 Seat Heating Control Module.
  4. Test for 850 Ω - 300 kΩ between the signal circuit terminal 20 X4 and the low reference circuit terminal 8 X2.
    • If less than the specified range, test for a short between the signal and low reference circuits. If the circuits test normal, replace the E14D Seat Heating Element - Passenger Cushion.
    • If greater than the specified range, test the signal and low reference circuits for a short to voltage or an open/high resistance. If the circuits test normal, replace the E14D Seat Heating Element - Passenger Cushion.
  5. Connect the X1, X2 and X4 harness connectors at the K29 Seat Heating Control Module.
  6. Disconnect the harness connector at the seat cushion heater element/temperature sensor.
  7. Ignition ON, test for 4.8 - 5.2 V between the signal circuit terminal C and ground.
    • If less than the specified range, test the signal circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the K29 Seat Heating Control Module.
    • If greater than the specified range, test the signal circuit for a short to voltage. If the circuit tests normal, replace the K29 Seat Heating Control Module.
  8. If all circuits test normal, replace the K29 Seat Heating Control Module.
scientia non olet · About LEMON Manuals