LEMON Manuals: Even more car manuals for everyone
Home >> Chevrolet >> 2010 >> Traverse LT, AWD >> Repair and Diagnosis >> External Pages >> Different car >> Section 479 (Seat Heating System And Seat Cooling System) >> Diagnostic Information and Procedures >> DTC B1935 or B2180: Left/Right Seat Back Heater (Without Memory A45) >> Circuit/System Testing

Circuit/System Testing

WARNING: This page is about a different car, the 2016 GMC Acadia, 2016 Chevrolet Traverse, and 2016 Buick Enclave. However, it is still accessible from the selected car via links, so may be relevant.

B1935 0A, B1935 0B, B1935 0C, B1935 0D, B1935 0E, B1935 04, or B1935 1F

  1. Ignition OFF, disconnect the X1 harness connector at the K29 Seat Heating Control Module.
    2. IMPORTANT:

    When measuring the resistance, the resistance values are based on the seat being at room temperature of 20°C (68°F).

  2. Test for 6-14.1 Ω between the control circuit terminal 3 and the control circuit terminal 1.
    • If less than the specified range, test for a short between the control circuits. If the circuits test normal, replace the E14A Seat Heating Element - Driver Back.
    • If greater than the specified range, test the control circuits for an open/high resistance. If the circuits test normal, replace the E14A Seat Heating Element - Driver Back.
  3. Ignition OFF, disconnect the X2 and X4 harness connectors at the K29 Seat Heating Control Module.
  4. Test for 3.3 k-300 kΩ between the signal circuit terminal 19 X4 and the low reference circuit terminal 5 X2.
    • If less than the specified range, test for a short between the signal and low reference circuits. If the circuits test normal, replace the E14A Seat Heating Element - Driver Back.
    • If greater than the specified range, test the signal circuit and low reference circuit for a short to voltage or an open/high resistance. If the circuits test normal, replace the E14A Seat Heating Element - Driver Back.
  5. Ignition OFF, connect the X1, X2, and X4 harness connectors at the K29 Seat Heating Control Module.
  6. Disconnect the harness connector at the E14A Seat Heating Element - Driver Back.
  7. Ignition ON, test for 4.8-5.2 V between the signal circuit terminal 3 and ground.
    • If less than the specified range, test the signal circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the K29 Seat Heating Control Module.
    • If greater than the specified range, test the signal circuit for a short to voltage. If the circuit tests normal, replace the K29 Seat Heating Control Module.
  8. If all circuits test normal, replace the K29 Seat Heating Control Module.

B2180 0A, B2180 0B, B2180 0C, B2180 0D, B2180 0E, B2180 04, or B2180 1F

  1. Ignition OFF, disconnect the X1 harness connector at the K29 Seat Heating Control Module.
    2. IMPORTANT:

    When measuring the resistance, the resistance values are based on the seat being at room temperature of 20°C (68°F).

  2. Test for 6-14.3 Ω between the control circuit terminal 6 and the control circuit terminal 4.
    • If greater than the specified value, test the control circuits for an open/high resistance. If the circuits test normal, replace the E14C Seat Heating Element - Passenger Back.
    • If less than the specified range, test for a short between the control circuits. If the circuits test normal, replace the E14C Seat Heating Element - Passenger Back.
  3. Ignition OFF, disconnect the X2 and X4 harness connectors at the K29 Seat Heating Control Module.
  4. Test for 3.3 k-300 kΩ between the signal circuit terminal 10 X4 and the low reference circuit terminal 7 X2.
    • If less than the specified range, test for a short between the signal and low reference circuits. If the circuits test normal, replace the E14C Seat Heating Element - Passenger Back.
    • If greater than the specified range, test the signal circuit and low reference circuit for a short to voltage or an open/high resistance. If the circuits test normal, replace the E14C Seat Heating Element - Passenger Back.
  5. Ignition OFF, connect the X1, X2, and X4 harness connectors at the K29 Seat Heating Control Module.
  6. Disconnect the harness connector at the E14C Seat Heating Element - Passenger Back.
  7. Ignition ON, test for 4.8-5.2 V between the signal circuit terminal 3 and ground.
    • If less than the specified range, test the signal circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the K29 Seat Heating Control Module.
    • If greater than the specified range, test the signal circuit for a short to voltage. If the circuit tests normal, replace the K29 Seat Heating Control Module.
  8. If all circuits test normal, replace the K29 Seat Heating Control Module.
scientia non olet · About LEMON Manuals