LEMON Manuals: Even more car manuals for everyone
Home >> Chevrolet >> 2010 >> Traverse LT, AWD >> Repair and Diagnosis >> External Pages >> Different car >> Section 479 (Seat Heating System And Seat Cooling System) >> Diagnostic Information and Procedures >> DTC B1925 or B2170: Seat Heater (With Memory A45, without KB6) >> Circuit/System Testing

Circuit/System Testing

WARNING: This page is about a different car, the 2016 GMC Acadia, 2016 Chevrolet Traverse, and 2016 Buick Enclave. However, it is still accessible from the selected car via links, so may be relevant.

B1925 02 or B1925 05

  1. Ignition OFF, disconnect the X2 and X5 harness connectors at the K40 Seat Memory Control Module.
    2. IMPORTANT:

    When measuring the resistance, the resistance values are based on the seat being at room temperature of 20°C (68°F).

  2. Test for 3.3 k-300 kΩ between the signal circuit terminal 1 X5 and the low reference circuit terminal 3 X2.
    • If less than the specified range, test for a short between the signal and low reference circuits. If the circuits test normal, replace the E14B Seat Heating Element - Driver Cushion.
    • If greater than the specified range, test the signal circuit and low reference circuit for a short to voltage or an open/high resistance. If the circuits test normal, replace the E14B Seat Heating Element - Driver Cushion.
  3. Ignition OFF, connect the X2 and X5 harness connectors at the K40 Seat Memory Control Module.
  4. Disconnect the harness connector at the E14B Seat Heating Element - Driver Cushion.
  5. Ignition ON, test for 4.8-5.2 V between the signal circuit terminal 3 and ground.
    • If less than the specified range, test the signal circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the K40 Seat Memory Control Module.
    • If greater than the specified range, test the signal circuit for a short to voltage. If the circuit tests normal, replace the K40 Seat Memory Control Module.
  6. If all circuits test normal, replace the K40 Seat Memory Control Module.

B2170 02 or B2170 05

  1. Ignition OFF, disconnect the X2 and X5 harness connectors at the K40 Seat Memory Control Module.
    2. IMPORTANT:

    When measuring the resistance, the resistance values are based on the seat being at room temperature of 20°C (68°F).

  2. Test for 3.3 k-300 kΩ between the signal circuit terminal 2 X5 and the low reference circuit terminal 6 X2.
    • If less than the specified range, test for a short between the signal and low reference circuits. If the circuits test normal, replace the E14D Seat Heating Element - Passenger Cushion.
    • If greater than the specified range, test the signal circuit and low reference circuit for a short to voltage or an open/high resistance. If the circuits test normal, replace the E14D Seat Heating Element - Passenger Cushion.
  3. Ignition OFF, connect the X2 and X5 harness connectors at the K40 Seat Memory Control Module.
  4. Disconnect the harness connector at the E14D Seat Heating Element - Passenger Cushion.
  5. Ignition ON, test for 4.8-5.2 V between the signal circuit terminal 3 and ground.
    • If less than the specified range, test the signal circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the K40 Seat Memory Control Module.
    • If greater than the specified range, test the signal circuit for a short to voltage. If the circuit tests normal, replace the K40 Seat Memory Control Module.
  6. If all circuits test normal, replace the K40 Seat Memory Control Module.
scientia non olet · About LEMON Manuals