LEMON Manuals: Even more car manuals for everyone
Home >> Chevrolet >> 2010 >> HHR LS, Standard >> Repair and Diagnosis >> Engine Mechanical >> Mechanical >> Engine Mechanical - 2.2L Or 2.4L - Specifications >> Specifications >> Engine Mechanical Specifications (LAP, LE8)

Engine Mechanical Specifications (LAP, LE8)

Application Specification
Metric English
General Data
  • Engine Type
 Inline 4 Cylinder
  • Displacement
 2.2 L 134 CID
  • RPO
 LAP, LE8
  • Liter (VIN)
 F
  • Bore
 85.992-86.008 mm 3.3855-3.3861 in
  • Stroke
 94.6 mm 3.727 in
  • Compression Ratio
 10.0:1
Balance Shaft
  • Bearing Clearance
 0.030-0.060 mm 0.0012-0.0024 in
  • Bearing Diameter - Inside - Carrier
 20.050-20.063 mm 0.7894-0.7899 in
  • Bearing Diameter - Outside - Carrier
 41.975-41.995 mm 1.6526-1.6534 in
  • Bearing Journal Diameter
 20.000-20.020 mm 0.7874-0.7882 in
  • Bushing Clearance
 0.033-0.102 mm 0.0013-0.0040 in
  • Bushing Diameter - Inside
 36.776-36.825 mm 1.4479-1.4498 in
  • Bushing Journal Diameter
 36.723-36.743 mm 1.4458-1.4466 in
  • End Play
 0.050-0.300 mm 0.0020-0.0118 in
Block
  • Balance Shaft Bearing Bore Diameter - Carrier
 42.000-42.016 mm 1.6535-1.6542 in
  • Balance Shaft Bushing Bore Diameter
 40.763-40.776 mm 1.6048-1.6054 in
  • Crankshaft Main Bearing Bore Diameter
 64.068-64.082 mm 2.5224-2.5229 in
  • Cylinder Bore Diameter
 85.992-86.008 mm 3.3855-3.3861 in
  • Cylinder Bore Out-of-Round - Maximum
 0.010 mm 0.0004 in
  • Cylinder Bore Taper - Maximum
 0.010 mm 0.0004 in
  • Cylinder Head Deck Surface Flatness - Transverse
 0.030 mm 0.0012 in
  • Cylinder Head Deck Surface Flatness - Longitude
 0.050 mm 0.002 in
  • Cylinder Head Deck Surface Flatness - Overall
 0.08 mm 0.0031 in
Camshaft
  • Camshaft End Play
 0.040-0.144 mm 0.0016-0.0057 in
  • Camshaft Journal Diameter
 26.935-26.960 mm 1.0604-1.0614 in
  • Camshaft Thrust Surface
 21.000-21.052 mm 0.8268-0.8252 in
Connecting Rod
  • Connecting Rod Bearing Clearance
 0.029-0.073 mm 0.0011-0.0029 in
  • Connecting Rod Bore Diameter - Bearing End
 52.118-52.134 mm 2.0519-2.05252 in
  • Connecting Rod Bore Diameter - Pin End
 20.007-20.017 mm 0.7877-0.7881 in
  • Connecting Rod Side Clearance
 0.070-0.370 mm 0.0028-0.0146 in
  • Connecting Rod Straightness - Bend - Maximum
 0.021 mm 0.0083 in
  • Connecting Rod Straightness - Twist - Maximum
 0.04 mm 0.0157 in
Crankshaft
  • Connecting Rod Journal Diameter
 49.000-49.014 mm 1.9291-1.9297 in
  • Crankshaft End Play
 0.050-0.380 mm 0.0012-0.0150 in
  • Crankshaft Main Bearing Clearance
 0.031-0.067 mm 0.0012-0.0026 in
  • Crankshaft Main Journal Diameter
 55.994-56.008 mm 2.2045-2.2050 in
Cylinder Head
  • Overall Height, Minimum
 128.9 mm 5.07 in
  • Surface Flatness - Block Deck - Transverse
 0.030 mm 0.0012 in
  • Surface Flatness - Block Deck - Longitude
 0.050 mm 0.002 in
  • Surface Flatness - Block Deck - Overall
 0.1 mm 0.004 in
  • Valve Guide Bore - Exhaust
 6.000-6.012 mm 0.2362-0.2367 in
  • Valve Guide Bore - Intake
 6.000-6.012 mm 0.2362-0.2367 in
  • Valve Lifter Bore Diameter - Stationary Lash Adjusters
 12.013-12.037 mm 0.4730-0.4739 in
Lubrication System
  • Oil Pressure - Minimum - @1000 RPM @ 90°C (194°F)
 206.84-482.63 kPa 30-70 psi
  • Oil Capacity
 4.8L 5.0 quarts
Piston Rings
  • Piston Ring End Gap - First Compression Ring
 0.20-0.35 mm 0.008-0.014 in
  • Piston Ring End Gap - Second Compression Ring
 0.35-0.55 mm 0.014-0.022 in
  • Piston Ring End Gap - Oil Control Ring - Rails
 0.25-0.75 mm 0.010-0.030 in
  • Piston Ring to Groove Clearance - First Compression Ring
 0.04-0.08 mm 0.0015-0.0031 in
  • Piston Ring to Groove Clearance - Second Compression Ring
 0.030-0.069 mm 0.0012-0.0027 in
  • Piston Ring to Groove Clearance - Oil Control Ring
 0.058-0.207 mm 0.0023-0.0081 in
  • Piston Ring Thickness - Upper First Compression Ring
 1.170-1.190 mm 0.0461-0.0469 in
  • Piston Ring Thickness - Upper Second Compression Ring
 1.471-1.490 mm 0.0579-0.0587 in
  • Piston Ring Thickness - Oil Control Ring - Rail - Maximum
 0.473 mm 0.0186 in
  • Piston Ring Thickness - Oil Control Ring - Spacer
 0.929-1.006 mm 0.0366-0.0396 in
Pistons and Pins
  • Pin - Piston Pin Clearance to Connecting Rod Bore
 0.007-0.020 mm 0.0003-0.0008 in
  • Pin - Piston Pin Clearance to Piston Pin Bore
 0.004-0.012 mm 0.0002-0.0005 in
  • Pin - Piston Pin Diameter
 19.997-20.000 mm 0.7873-0.7874 in
  • Pin - Piston Pin End Play
 0.210-1.266 mm 0.0083-0.0498 in
  • Piston - Piston Diameter - @14.5 mm up
 85.967-85.982 mm 3.3845-3.3851 in
  • Piston - Piston Pin Bore Diameter
 20.002-20.007 mm 0.07875-0.7877 in
  • Piston - Piston Ring Groove Width - Top
 1.23-1.25 mm 0.0484-0.0492 in
  • Piston - Piston Ring Groove Width - Second
 1.52-1.54 mm 0.0598-0.0606 in
  • Piston - Piston Ring Groove Width - Oil Control
 2.01-2.03 mm 0.0791-0.0799 in
  • Piston - Piston To Bore Clearance, without polymer
 0.010-0.041 mm 0.0004-0.0016 in
Valve System
  • Valve Lifters - Valve Lifter Diameter - Stationary Lash Adjuster
 11.986-12.000 mm 0.0005-0.0020 in
  • Valve Lifters - Valve Lifter-to-Bore Clearance - Stationary Lash Adjuster
 0.013-0.051 mm 3.2210-3.2299 in
  • Valve Springs - Valve Spring Load - Closed - @32.5 mm
 245.0-271.0 N. - Eng Spec.
  • Valve Springs - Valve Spring Load - Open - @22.5 mm
 525.0-575.0 N. - Eng Spec.
  • Valves - Valve Face Runout - Maximum
 0.04 mm 0.0016 in
  • Valves - Valve Seat Runout - Maximum
 0.05 mm 0.0020 in
  • Valves - Valve Stem Diameter - Intake
 5.955-5.970 mm 0.2344-0.2355 in
  • Valves - Valve Stem Diameter - Exhaust
 5.935-5.950 mm 0.2337-0.2343 in
  • Valves - Valve Stem to Guide Clearance - Intake
 0.030-0.057 mm 0.0012-0.0022 in
  • Valves - Valve Stem to Guide Clearance - Exhaust
 0.050-0.077 mm 0.0020-0.0026 in
scientia non olet · About LEMON Manuals