Paddle Shifter + (Upshift Switch) Circuit Troubleshooting

WARNING: This page is about a different car, the 2011 Honda Insight and 2010 Honda Insight. However, it is still accessible from the selected car via links, so may be relevant.

SRS components are located in this area. Review the SRS component (see COMPONENT LOCATION INDEX ) locations and the precautions and procedures (see PRECAUTIONS AND PROCEDURES ) before doing repair or service.

Remove the steering wheel (see STEERING WHEEL REMOVAL ).
Check for continuity between cable reel subharness 20P connector terminals No. 14 and No. 12 when pressing and releasing the paddle shifter + (upshift switch).

Fig 1: Checking Continuity Between Cable Reel Subharness 20P Connector Terminals 14 And 12
Courtesy of AMERICAN HONDA MOTOR CO., INC.

Is there continuity when pressing the paddle shifter + (upshift switch) and no continuity when the paddle shifter + (upshift switch) is released?

YES -go to step 5.

NO -go to step 3.
Disconnect the paddle shifter + (upshift switch) connector.
Check for continuity between paddle shifter + (upshift switch) connector terminals No. 1 and No. 2 when pressing and releasing the paddle shifter + (upshift switch).

Fig 2: Checking Continuity Between Paddle Shifter + (Upshift Switch) Terminals 1 And 2
Courtesy of AMERICAN HONDA MOTOR CO., INC.

Is there continuity when pressing the paddle shifter + (upshift switch) and no continuity when the paddle shifter + (upshift switch) is released?

YES -Replace the cable reel subharness.

NO -Replace the paddle shifter + (upshift switch) (see PADDLE SHIFTER + (UPSHIFT SWITCH) OR PADDLE SHIFTER - (DOWNSHIFT SWITCH) REPLACEMENT ).
Remove the cable reel (see CABLE REEL REPLACEMENT ).
Check for continuity between cable reel 20P connector terminal No. 2 and body ground.

Fig 3: Checking Continuity Between Cable Reel 20P Connector Terminal 2 And Body Ground
Courtesy of AMERICAN HONDA MOTOR CO., INC.

Is there continuity?

YES -go to step 7.

NO -Repair an open in the wire between cable reel 20P connector terminal No. 2 and body ground (G502), or repair poor body ground (G502).
Check for continuity between cable reel 20P connector terminal No. 14 and body ground.

Fig 4: Checking Continuity Between Cable Reel 20P Connector Terminal 14 And Body Ground
Courtesy of AMERICAN HONDA MOTOR CO., INC.

Is there continuity?

YES -Repair a short to body ground in wire between cable reel 20P connector terminal No. 14 and PCM connector terminal A30.

NO -go to step 8.
Turn the ignition switch to ON (II), and shift to S.
Measure the voltage between cable reel 20P connector terminals No. 2 and No. 14.

Fig 5: Measuring Voltage Between Cable Reel 20P Connector Terminals 2 And 14
Courtesy of AMERICAN HONDA MOTOR CO., INC.

Is there battery voltage?

YES -Replace the cable reel (see CABLE REEL REPLACEMENT ).

NO -go to step 10.
Turn the ignition switch to LOCK (0).
Jump the SCS line with the HDS.
Disconnect PCM connector A (44P).
Check for continuity between PCM connector terminal A30 and body ground.

Fig 6: Checking Continuity Between PCM Connector Terminal A30 And Body Ground
Courtesy of AMERICAN HONDA MOTOR CO., INC.

Is there continuity?

YES -Repair a short to body ground in wire between cable reel 20P connector terminal No. 14 and PCM connector terminal A30.

NO -Check for loose or poor connections at PCM connector terminal A30. If the connection is OK, substitute a known-good PCM (see SUBSTITUTING THE PCM ) and recheck.