LEMON Manuals: Even more car manuals for everyone
Home >> Chevrolet >> 2007 >> Chevy Express G2500, Van Cargo, 6.6 6 >> Repair and Diagnosis >> External Pages >> Different variant/trim >> Section 20 (Engine Mechanical - 4.3L) >> Repair Instructions - On Vehicle >> Crankshaft Balancer Replacement >> Installation Procedure

Installation Procedure

WARNING: This page is about a different variant/trim than selected.
  1. Apply a small amount of grease to the crankshaft front cover oil seal sealing surface.
    2. Fig 1: View Of Crankshaft Balancer Weights
    GM334258Courtesy of GENERAL MOTORS CORP.
  2. Look to ensure that the front groove pin (crankshaft balancer) is installed in the proper location if applicable.

    The length and location of the pins must be the same as the original length and location.

    3. Fig 2: Installing Crankshaft Balancer
    GM188059Courtesy of GENERAL MOTORS CORP.
  3. Apply a small amount of adhesive onto the crankshaft balancer keyway in order to seal the crankshaft balancer keyway and crankshaft joint. Refer to Sealers, Adhesives, and Lubricants  for the correct part number.
  4. Align the keyway of the crankshaft balancer with the crankshaft balancer key.
  5. Install the crankshaft balancer onto the end of the crankshaft.
    6. Fig 3: Pressing The Crankshaft Balancer Onto The Crankshaf Using J 23523-F
    GM4065Courtesy of GENERAL MOTORS CORP.
  6. Use the J 23523-F  in order to press the crankshaft balancer onto the crankshaft. See Special Tools .
      NOTE: Refer to Fastener Notice .
    1. Install the J 23523-F  plate and bolts onto the front of the crankshaft balancer. See Special Tools .

      Tighten:  Tighten the plate bolts to 25 N.m (18 lb ft).

    2. Install the J 23523-F  screw into the end for the crankshaft. See Special Tools .
    3. Install the J 23523-F  bearing, the washer, and the nut onto the screw. See Special Tools .
    4. Rotate the J 23523-F  nut clockwise until the crankshaft balancer hub is completely seated against the crankshaft position sensor reluctor ring. See Special Tools .
  7. Remove the J 23523-F  . See Special Tools .
    8. Fig 4: View Of Crankshaft Pulley & Bolts
    GM188055Courtesy of GENERAL MOTORS CORP.
  8. Install the crankshaft pulley and bolts.

    Tighten:  Tighten the crankshaft pulley bolts to 58 N.m (43 lb ft).

    9. Fig 5: Crankshaft Balancer Washer
    GM342203Courtesy of GENERAL MOTORS CORP.
  9. Ensure that the crown of the crankshaft balancer washer (2) is faced away from the engine.
    10. Fig 6: View Of Crankshaft Balancer Washer & Bolt
    GM173172Courtesy of GENERAL MOTORS CORP.
  10. Install the crankshaft balancer washer and the bolt.

    Tighten:  Tighten the crankshaft balancer bolt to 95 N.m (70 lb ft).

  11. Install the drive belt. Refer to Drive Belt Replacement .
  12. Install the fan shroud assembly. Refer to Engine Coolant Fan Lower Shroud Replacement (4.3L, 4.8L, 5.3L, 6.0L) .
  13. Connect the battery negative cable. Refer to Battery Negative Cable Disconnection and Connection .
scientia non olet · About LEMON Manuals