Chime Inoperative
Chime Inoperative
| Step | Action | Value(s) | Yes | No |
|---|---|---|---|---|
| Schematic Reference: Audible Warnings Schematics Connector End View Reference: Data Communication Connector End Views DEFINITION: One or more chime functions are inoperative. |
||||
| 1 | Did you perform the Diagnostic System Check - Vehicle? | - | Go to Step 2 | Go to Diagnostic System Check - Vehicle |
| 2 |
|
- | Go to Testing for Intermittent Conditions and Poor Connections | Go to Step 3 |
| 3 | Is the vehicle equipped with a chime module (UL5)? | - | Go to Step 5 | Go to Step 4 |
| 4 |
|
- | Go to Step 5 | Go to Speakers Inoperative - One or More |
| 5 |
|
- | Go to Step 7 | Go to Step 6 |
| 6 |
|
- | Go to Step 12 | Go to Step 8 |
| 7 |
|
- | Go to Step 13 | Go to Step 10 |
| 8 | Test the signal circuit of the ignition key alarm switch for an open, for a high resistance, or for a short to voltage. Refer to Circuit Testing
and Wiring Repairs
. Did you find and correct the condition? |
- | Go to Step 20 | Go to Step 9 |
| 9 | Test the ground circuit of the ignition key alarm switch for an open or for a high resistance. Refer Circuit Testing
and Wiring Repairs
. Did you find and correct the condition? |
- | Go to Step 20 | Go to Step 14 |
| 10 | Test the signal circuit of the driver door ajar switch for an open, for a high resistance, or for a short to voltage. Refer to Circuit Testing
and Wiring Repairs
. Did you find and correct the condition? |
- | Go to Step 20 | Go to Step 11 |
| 11 | Test the ground circuit of the driver door ajar switch for an open or for a high resistance. Refer to Circuit Testing
and Wiring Repairs
. Did you find and correct the condition? |
- | Go to Step 20 | Go to Step 15 |
| 12 | Inspect for poor connections at the harness connector of the BCM. Refer to Testing for Intermittent Conditions and Poor Connections
and Connector Repairs
. Did you find and correct the condition? |
- | Go to Step 20 | Go to Step 16 |
| 13 | Inspect for poor connections at the harness connector of the driver door ajar switch. Refer to Testing for Intermittent Conditions and Poor Connections
and Connector Repairs
. Did you find and correct the condition? |
- | Go to Step 20 | Go to Step 17 |
| 14 | Inspect for poor connections at the harness connector of the ignition key alarm switch. Refer to Testing for Intermittent Conditions and Poor Connections
and Connector Repairs
. Did you find and correct the condition? |
- | Go to Step 20 | Go to Step 18 |
| 15 | Inspect for poor connections at the harness connector of the chime module. Refer to Testing for Intermittent Conditions and Poor Connections
and Connector Repairs
. Did you find and correct the condition? |
- | Go to Step 20 | Go to Step 19 |
| 16 | Replace the BCM. Refer to Control Module References
for replacement, setup, and programming. Did you complete the replacement? |
- | Go to Step 20 | - |
| 17 | Replace the driver door ajar switch. Refer to Front Side Door Lock Replacement
. Did you complete the replacement? |
- | Go to Step 20 | - |
| 18 | Replace the ignition key alarm switch. Refer to Ignition and Start Switch Replacement
. Did you complete the replacement? |
- | Go to Step 20 | - |
| 19 | Replace the chime module. Refer to Control Module References
for replacement, setup, and programming. Did you complete the replacement? |
- | Go to Step 20 | - |
| 20 | Operate the system in order to verify the repair. Did you correct the condition? |
- | System OK | Go to Step 2 |