LEMON Manuals: Even more car manuals for everyone
Home >> Chevrolet >> 2006 >> Silverado 1500 HD, 4WD >> Repair and Diagnosis >> External Pages >> Different car >> Section 880 (Engine Controls And Fuel - 4.8L, 5.3L, 6.0L And 6.2L - Introduction (2 Of 2)) >> Repair Instructions >> Fuel Hose/Pipes Replacement - Chassis (1500 Regular Cab) >> Installation Procedure

Installation Procedure

WARNING: This page is about a different car, the 2007 GMC Sierra, 2007 GMC Cab & Chassis Sierra, 2007 Chevrolet Silverado, and 2007 Chevrolet Cab & Chassis Silverado. However, it is still accessible from the selected car via links, so may be relevant.
    Fig 1: EVAP Lines
    GM1855296Courtesy of GENERAL MOTORS CORP.
  1. Position and install the fuel/EVAP line assembly to the vehicle.
  2. Install the fuel/EVAP line bracket locator tab to the frame.
  3. Install the fuel/EVAP line clips to the frame and crossmember.
    4. NOTE: Refer to Fastener Notice .
  4. Install the fuel/EVAP line bracket bolt (1).

    Tighten:  Tighten the bolt to 9 N.m (80 lb in).

  5. Install the fuel/EVAP line clip nut (2).

    Tighten:  Tighten the bolt to 20 N.m (15 lb ft).

  6. Remove the caps from the fuel and EVAP lines.
  7. Connect the fuel tank EVAP line quick connect fitting to the chassis line. Refer to Plastic Collar Quick Connect Fitting Service .
  8. Connect the fuel tank fuel feed line quick connect fitting to the chassis line. Refer to Plastic Collar Quick Connect Fitting Service .
    9. Fig 2: EVAP Canister Vent Solenoid Clipand EVAP Canister Vent Solenoid Pipe Clip
    GM1855649Courtesy of GENERAL MOTORS CORP.
  9. Unscure and position the EVAP canister vent solenoid clip (1) to the chassis EVAP line.
  10. Install the EVAP canister vent solenoid pipe clip (2) to the chassis EVAP line.
    11. Fig 3: Fuel Hose/Pipe Clip At Bracket On Transfer Case
    GM1855293Courtesy of GENERAL MOTORS CORP.
  11. If equipped with 4WD, install the fuel hose/pipe clip to the bracket on the transfer case.
  12. Install the fuel line clip to the bracket on the automatic transmission.
    13. Fig 4: View Of Fuel/Evaporative Emission Pipe & Bracket
    GM1701047Courtesy of GENERAL MOTORS CORP.
  13. Install the fuel pipe bracket nut to the bellhousing stud.

    Tighten:  Tighten the nut to 25 N.m (18 lb ft).

  14. Position and install the front propeller shaft, if required. Refer to Front Propeller Shaft Replacement .
  15. Lower the vehicle.
    16. Fig 5: View Of EVAP Canister Purge Tube & Quick Connect Fitting
    GM1696917Courtesy of GENERAL MOTORS CORP.
  16. Remove the caps from the fuel rail and EVAP line.
  17. Connect the EVAP line (1) quick connect fitting to the chassis EVAP line. Refer to Plastic Collar Quick Connect Fitting Service .
  18. Connect the fuel feed line (2) quick connect fitting to the fuel rail. Refer to Metal Collar Quick Connect Fitting Service .
  19. Install the fuel fill cap.
  20. Connect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection (w/Single Battery) or Battery Negative Cable Disconnection and Connection (w/Auxiliary Battery) or Battery Negative Cable Disconnection and Connection (w/Dual Batteries) .
  21. Use the following procedure in order to inspect for leaks:
    1. Turn the ignition ON, with the engine OFF, for 2 seconds.
    2. Turn the ignition OFF for 10 seconds.
    3. Turn the ignition ON, with the engine OFF.
    4. Inspect for fuel leaks.
  22. Install the intake manifold sight shield. Refer to Upper Intake Manifold Sight Shield Replacement .
scientia non olet · About LEMON Manuals