LEMON Manuals: Even more car manuals for everyone
Home >> Chevrolet >> 2006 >> Silverado 1500 HD, 4WD >> Repair and Diagnosis >> External Pages >> Different car >> Section 225 (Front Drive Axle) >> Repair Instructions >> Inner Shaft and/or Housing Replacement - Front Drive Axle >> Installation Procedure

Installation Procedure

WARNING: This page does not describe the selected car, but rather 6 other vehicles, including the 2003 GMC Savana Special, 2003 GMC Savana Camper Special, 2003 GMC Savana, 2003 Chevrolet RV Cutaway, and 2003 Chevrolet Cutaway. However, it is still accessible from the selected car via links, so may be relevant.
  1. Install the new inner axle shaft bearing and the new seal to the inner axle shaft housing. Refer to Inner Axle Seal and/or Bearing Replacement - Front Drive Axle .
    CAUTION: Do not nick or cut the inner axle shaft oil seal.
  2. Install the inner axle shaft into the inner axle housing.

    Do not install the inner axle shaft completely into the inner axle shaft housing at this time.

  3. Apply sealant GM P/N 1052942 (Canadian P/N 10953466) or equivalent to the inner axle housing to differential carrier sealing surface.
    Fig 1: Installing Inner Axle Shaft Into Inner Axle Shaft Housing
    G01216382Courtesy of GENERAL MOTORS CORP.
  4. Install the inner axle shaft housing with the inner axle shaft to the differential carrier assembly.
    Fig 2: Installing Inner Axle Shaft Housing With Shaft To Differential Carrier Assembly
    G01216383Courtesy of GENERAL MOTORS CORP.
    CAUTION: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.
  5. Install the inner axle shaft housing bolts.

    Tighten 

    Tighten the inner axle shaft housing bolts to 48 N.m (35 lb ft).

    Fig 3: Installing Inner Axle Shaft Housing Bolts
    G01216384Courtesy of GENERAL MOTORS CORP.
  6. Install the lower inner axle shaft housing bushing bolt and nut.
    Fig 4: Installing Lower Inner Axle Shaft Housing Bushing Bolt & Nut
    G01216385Courtesy of GENERAL MOTORS CORP.
  7. Install the upper inner axle shaft housing bushing bolt and nut.

    Tighten 

    Tighten the upper and lower inner axle shaft housing bushing bolts to 85 N.m (63 lb ft).

  8. Remove the support jack.
  9. Install the inner axle shaft into the differential case side gear by doing the following:
    1. Carefully guide the inner axle shaft through the inner axle housing until the retaining ring on the inner axle shaft contacts the differential case side gear.
    2. Install the inner axle shaft into the differential case side gear by tapping the retaining ring into the retaining groove using a soft-faced mallet and until the retaining ring on the inner axle shaft is fully seated within the groove in the differential case side gear.
    3. Pull back on the inner axle shaft to ensure that the inner axle shaft is properly retained in the differential case side gear.
  10. Install the wheel drive shaft to the inner axle shaft. Refer to AXLE SHAFTS .
  11. Fill the differential carrier assembly with axle lubricant. Use the proper fluid. Refer to Lubricant Replacement - Front Drive Axle .
  12. Lower the vehicle.
    Fig 5: Installing Upper Inner Axle Shaft Housing Bushing Bolt & Nut
    G01216386Courtesy of GENERAL MOTORS CORP.
scientia non olet · About LEMON Manuals