Conditions for Running the DTC

WARNING: This page is about a different variant/trim than selected.

P0133

DTCs P0068, P0101, P0102, P0103, P0106, P0107, P0108, P0112, P0113, P0116, P0117, P0118, P0120, P0121, P0122, P0123, P0125, P0128, P0201, P0202, P0203, P0204, P0220, P0222, P0223, P0442, P0443, P0446, P0449, P0455, P0496, P1516, P2101, P2119, P2135, P2176 are not set.
The Engine Coolant Temperature (ECT) Sensor parameter is more than 70°C (158°F).
The Ignition 1 Signal parameter is between 10-18 volts.
The Fuel Level Sensor parameter is more than 10 percent.
The Engine Run Time parameter is more than 200 seconds.
The Engine Speed parameter is between 1,000-3,500 RPM.
The Manifold Absolute Pressure (MAP) Sensor parameter is more than 30 kPa.
The Mass Airflow (MAF) Sensor parameter is between 11-50 g/s.
The Loop Status parameter is Closed.
The Throttle Position (TP) Indicated Angle parameter is more than 5 percent.
DTC P0133 runs once per drive cycle when the above conditions are met for 2 seconds.

P0134

DTCs P0068, P0101, P0102, P0103, P0106, P0107, P0108, P0112, P0113, P0116, P0117, P0118, P0120, P0121, P0122, P0123, P0125, P0128, P0201, P0202, P0203, P0204, P0220, P0222, P0223, P0442, P0443, P0446, P0449, P0455, P0496, P1516, P2101, P2119, P2135, P2176 are not set.
The Engine Coolant Temperature (ECT) Sensor parameter is more than 70°C (158°F).
The Ignition 1 Signal parameter is between 10-18 volts.
The engine run time is more than 200 seconds.
DTC P0134 runs continuously when the above conditions are met.

P0140

DTCs P0068, P0101, P0102, P0103, P0106, P0107, P0108, P0112, P0113, P0116, P0117, P0118, P0120, P0121, P0122, P0123, P0125, P0128, P0201, P0202, P0203, P0204, P0220, P0222, P0223, P0442, P0443, P0446, P0449, P0455, P0496, P1516, P2101, P2119, P2135, P2176 are not set.
The ECT Sensor parameter is more than 70°C (158°F).
The Ignition 1 Signal parameter is between 10-18 volts.
The Engine Run Time parameter is more than 200 seconds.
The Loop Status parameter is closed.
DTC P0140 runs once per drive cycle when the above conditions are met.

P1133

DTCs P0068, P0101, P0102, P0103, P0106, P0107, P0108, P0112, P0113, P0116, P0117, P0118, P0120, P0121, P0122, P0123, P0125, P0128, P0201, P0202, P0203, P0204, P0220, P0222, P0223, P0442, P0443, P0446, P0449, P0455, P0496, P1516, P2101, P2119, P2135, P2176 are not set.
The ECT Sensor parameter is more than 70°C (158°F).
The Engine Speed parameter is between 1,500-3,500 RPM.
The Ignition 1 Signal parameter is between 10-18 volts.
The Engine Run Time parameter is more than 200 seconds.
The Loop Status parameter is Closed.
The TP Indicated Angle parameter is more than 5 percent.
The Fuel Level Sensor parameter is more than 10 percent.
The MAP Sensor parameter is more than 30 kPa.
The MAF Sensor parameter is between 11-50 g/s.
DTC P1133 runs once per drive cycle when the above conditions are met for 2 seconds.