Conditions for Running the DTC

WARNING: This page is about a different variant/trim than selected.

P0131 Lean Test Enable

DTCs P0068, P0101, P0102, P0103, P0106, P0107, P0108, P0112, P0113, P0116, P0117, P0118, P0120, P0121, P0122, P0123, P0125, P0128, P0201, P0202, P0203, P0204, P0220, P0222, P0223, P0442, P0443, P0446, P0449, P0455, P0496, P1516, P2101, P2119, P2135, P2176 are not set.
The Loop Status parameter is Closed.
The Ignition 1 Signal parameter is between 10-18 volts.
The Fuel Level Sensor parameter is more than 10 percent.
The Throttle Position (TP) Indicated Angle parameter is between 15-50 percent.
DTC P0131 runs the lean test continuously when the above conditions are met for 2 seconds.

P0131 Power Enrichment Test Enable

DTCs P0068, P0101, P0102, P0103, P0106, P0107, P0108, P0112, P0113, P0116, P0117, P0118, P0120, P0121, P0122, P0123, P0125, P0128, P0201, P0202, P0203, P0204, P0220, P0222, P0223, P0442, P0443, P0446, P0449, P0455, P0496, P1516, P2101, P2119, P2135, P2176 are not set.
The Ignition 1 Signal parameter is between 10-18 volts.
The Fuel Level Sensor parameter is more than 10 percent.
The Engine Run Time parameter is more than 30 seconds.
DTC P0131 runs the power enrichment test continuously when the above conditions are met for 2 seconds.

P0132 Rich Test Enable

DTCs P0068, P0101, P0102, P0103, P0106, P0107, P0108, P0112, P0113, P0116, P0117, P0118, P0120, P0121, P0122, P0123, P0125, P0128, P0201, P0202, P0203, P0204, P0220, P0222, P0223, P0442, P0443, P0446, P0449, P0455, P0496, P1516, P2101, P2119, P2135, P2176 are not set.
The Loop Status parameter is Closed.
The Ignition 1 Signal parameter is between 10-18 volts.
The Fuel Level Sensor parameter is more than 10 percent.
The Throttle Position (TP) Sensor parameter is between 0-50 percent.
DTC P0132 runs the rich test continuously when the above conditions are met for 2 seconds.

P0132 Decel Fuel Cut-Off Test Enable

DTCs P0068, P0101, P0102, P0103, P0106, P0107, P0108, P0112, P0113, P0116, P0117, P0118, P0120, P0121, P0122, P0123, P0125, P0128, P0201, P0202, P0203, P0204, P0220, P0222, P0223, P0442, P0443, P0446, P0449, P0455, P0496, P1516, P2101, P2119, P2135, P2176 are not set.
The Loop Status parameter is Closed.
The Ignition 1 Signal parameter is between 10-18 volts.
The Fuel Level Sensor parameter is more than 10 percent.
The Engine Run Time parameter is more than 30 seconds.
DTC P0132 runs the decel fuel cut-off test continuously when the above conditions are met for 2 seconds.

P0137 Lean Test Enable

DTCs P0068, P0101, P0102, P0103, P0106, P0107, P0108, P0112, P0113, P0116, P0117, P0118, P0120, P0121, P0122, P0123, P0125, P0128, P0201, P0202, P0203, P0204, P0220, P0222, P0223, P0442, P0443, P0446, P0449, P0455, P0496, P1516, P2101, P2119, P2135, P2176 are not set.
The Loop Status parameter is Closed.
The Ignition 1 Signal parameter is between 10-18 volts.
The Fuel Level Sensor parameter is more than 10 percent.
The TP Sensor parameter is between 15-50 percent.
DTC P0137 runs the lean test continuously when the above conditions are met for 2 seconds.

P0137 Power Enrichment Test Enable

DTCs P0068, P0101, P0102, P0103, P0106, P0107, P0108, P0112, P0113, P0116, P0117, P0118, P0120, P0121, P0122, P0123, P0125, P0128, P0201, P0202, P0203, P0204, P0220, P0222, P0223, P0442, P0443, P0446, P0449, P0455, P0496, P1516, P2101, P2119, P2135, P2176 are not set.
The Loop Status parameter is Closed.
The Ignition 1 Signal parameter is between 10-18 volts.
The Fuel Level Sensor parameter is more than 10 percent.
The Engine Run Time parameter is more than 30 seconds.
The Power Enrichment parameter is active for more than 2 seconds.
DTC P0137 runs the power enrichment test during each occurrence of power enrichment, when the above conditions are met for 3 seconds.

P0138 Rich Test Enable

DTCs P0068, P0101, P0102, P0103, P0106, P0107, P0108, P0112, P0113, P0116, P0117, P0118, P0120, P0121, P0122, P0123, P0125, P0128, P0201, P0202, P0203, P0204, P0220, P0222, P0223, P0442, P0443, P0446, P0449, P0455, P0496, P1516, P2101, P2119, P2135, P2176 are not set.
The Loop Status parameter is Closed.
The Ignition 1 Signal parameter is between 10-18 volts.
The Fuel Level Sensor parameter is more than 10 percent.
The TP Sensor parameter is between 0-50 percent.
DTC P0138 runs the rich test continuously when the above conditions are met for 2 seconds.

P0138 Decel Fuel Cut-Off Test Enable

DTCs P0068, P0101, P0102, P0103, P0106, P0107, P0108, P0112, P0113, P0116, P0117, P0118, P0120, P0121, P0122, P0123, P0125, P0128, P0201, P0202, P0203, P0204, P0220, P0222, P0223, P0442, P0443, P0446, P0449, P0455, P0496, P1516, P2101, P2119, P2135, P2176 are not set.
The Loop Status parameter is Closed.
The Ignition 1 Signal parameter is between 10-18 volts.
The Fuel Level Sensor parameter is more than 10 percent.
The Engine Run Time parameter is more than 30 seconds.
The decel fuel cut-off (DFCO) is active.
DTC P0138 runs the decel. fuel cut-off test during each occurrence of the decel. fuel cut-off, when the above conditions are met for 2 seconds.

P2A00

DTCs P0068, P0101, P0102, P0103, P0106, P0107, P0108, P0112, P0113, P0116, P0117, P0118, P0120, P0121, P0122, P0123, P0125, P0128, P0201, P0202, P0203, P0204, P0220, P0222, P0223, P0442, P0443, P0446, P0449, P0455, P0496, P1516, P2101, P2119, P2135, P2176 are not set.
The Engine Run Time parameter is more than 100 seconds.
The Engine speed parameter is between 1,000-3,400 RPM.
The Ignition 1 Signal parameter is between 10-18 volts.
The Mass Airflow (MAF) Sensor parameter is between 10-30 g/s.
The ECT Sensor parameter is more than 70°C (158°F).
DTC P2A00 runs continuously when the above conditions are met for 5 seconds.

P2A01 Passive Test

DTCs P0030, P0036, P0053, P0054, P0068, P0101, P0102, P0103, P0106, P0107, P0108, P0112, P0113, P0116, P0117, P0118, P0120, P0121, P0122, P0123, P0125, P0128, P0131, P0132, P0133, P0134, P0135, P0137, P0138, P0140, P0141, P0201, P0202, P0203, P0204, P0220, P0222, P0223, P0442, P0443, P0446, P0449, P0455, P0496, P1133, P1516, P2101, P2119, P2135, P2176, P2A00 are not set.
The engine is running.
The Engine Run Time parameter is less than 13.3 minutes.
DTC P2A01 runs the passive test once per drive cycle when the above conditions are met.

P2A01 Intrusive Test

DTCs P0030, P0036, P0053, P0054, P0068, P0101, P0102, P0103, P0106, P0107, P0108, P0112, P0113, P0116, P0117, P0118, P0120, P0121, P0122, P0123, P0125, P0128, P0131, P0132, P0133, P0134, P0135, P0137, P0138, P0140, P0141, P0201, P0202, P0203, P0204, P0220, P0222, P0223, P0442, P0443, P0446, P0449, P0455, P0496, P1133, P1516, P2101, P2119, P2135, P2176, P2A00 are not set.
The Engine Run Time parameter is more than 13.3 minutes.
The ignition 1 Signal parameter is between 10-18 volts.
The MAF sensor parameter is between 14-100 g/s.
The Engine Speed parameter is between 1,000-5,000 RPM.
The Vehicle Speed parameter is between 32-129 km/h (20-80 mph).
The Short Term FT parameter is between -20 and +20 percent.
The maximum number of intrusive attempts is less than 50.
DTC P2A01 runs the intrusive test once per drive cycle when the above conditions are met for 1 second.