LEMON Manuals: Even more car manuals for everyone
Home >> Chevrolet >> 2006 >> Cobalt LTZ >> Repair and Diagnosis >> External Pages >> Different car >> Section 698 (Manual Transmission - GETRAG (M86)) >> Diagnostic Information and Procedures >> DTC P0833 >> Test Description

Test Description

WARNING: This page is about a different car, the 2007 Pontiac G5 Pursuit, 2007 Pontiac G5, and 2007 Chevrolet Cobalt. However, it is still accessible from the selected car via links, so may be relevant.

The number below refers to the step number on the diagnostic table.

  1. 2:  This test confirms if the scan tool is receiving a clutch switch position signal.
  2. 3:  This step inspects the clutch pedal connector and adjustment.
DTC P0833

Step Action Values Yes No
1 Did you perform the Diagnostic System Check - Vehicle? - Go to Step 2  Go to DIAGNOSTIC SYSTEM CHECK - VEHICLE
2 
  1. Install a scan tool.
  2. Turn ON the ignition, with the engine OFF.
    3. IMPORTANT: Before clearing the DTCs, use the scan tool in order to record the Freeze Frame and Failure Records for reference. The Clear Info function will erase the data.
  3. Use the scan tool to monitor the clutch pedal position switch parameter.
  4. Apply and release the clutch pedal several times.
Does the scan tool indicate a change in state when the clutch pedal is either applied or released?		 - Refer to Testing for Intermittent Conditions and Poor Connections Go to Step 3 
3  Inspect the clutch pedal position switch and the connector.
Does the clutch switch or the connector require service?		 - Go to Step 11  Go to Step 4 
4 Inspect the EMISSION fuse for an open. Refer to Circuit Protection - Fuses .
Is the EMISSION fuse open?		 - Go to Step 9  Go to Step 5 
5 Using a DMM, measure voltage at the EMISSION fuse.
Does the DMM indicate the specified value?		 B+ Go to Step 6  Go to Step 12 
6
  1. Turn OFF the ignition.
  2. Disconnect the clutch pedal position switch connector.
  3. Turn ON the ignition with the engine OFF.
  4. Using a DMM, measure the voltage at the ignition 1 voltage circuit at the switch connector.
Does the DMM indicate the specified value?		 B+ Go to Step 7  Go to Step 13 
7
  1. Clear all DTCs.
  2. Use the scan tool to monitor the clutch pedal position switch parameter.
  3. Use a fused jumper wire to repeatedly connect and disconnect pin 1 and pin 2 of the clutch pedal position switch electrical connector.
Does the scan tool display that the clutch is applying and releasing?		 - Go to Step 15  Go to Step 8 
8
  1. Turn the ignition switch OFF.
  2. Disconnect C1 at the ECM.
  3. Using the DMM, test for continuity and a short to voltage on the clutch pedal position switch signal circuit.
Did you find a short to voltage, high resistance or an open on the clutch pedal position switch signal circuit?		 - Go to Step 14  Go to Step 16 
9
  1. Turn the ignition switch OFF.
  2. Remove the EMISSION fuse.
  3. Disconnect the clutch pedal position switch connector and C2 at the ECM.
  4. Using a DMM, test for a short to ground on the ignition 1 voltage circuit at the switch connector.
Is the ignition 1 voltage circuit grounded?		 - Go to Step 13  Go to Step 10 
10 Using a DMM, test for a short to ground on the clutch pedal position switch signal circuit at the switch connector.
Is the clutch pedal position switch signal circuit grounded?		 - Go to Step 14  Go to Step 15 
11 Replace the clutch pedal position switch, or repair the connector, as necessary. Refer to Clutch Pedal Position Switch Replacement or Connector Repairs .
Did you complete the repair?		 - Go to Step 17  -
12 Repair the power distribution circuit to the EMISSION fuse.
Did you complete the repair?		 - Go to Step 17  -
13 Repair the open, high resistance or short to ground in the ignition 1 voltage circuit or a parallel circuit that uses the brake fuse.
Refer to Wiring Repairs .
Did you complete the repair?		 - Go to Step 17  -
14 Repair the open, high resistance, short to ground or short to voltage in the clutch pedal position switch signal circuit.
Refer to Wiring Repairs .
Did you complete the repair?		 - Go to Step 17  -
15 Replace the clutch pedal position switch.
Refer to Clutch Pedal Position Switch Replacement .
Is the action complete?		 - Go to Step 17  -
16 Replace the ECM.
Refer to Control Module References for replacement, setup, and programming.
Is the action complete?		 - Go to Step 17  -
17
  1. Select the DTC.
  2. Select Clear Info.
  3. Operate the vehicle from 0 km/h (0 mph) to above 38 km/h (24 mph) then back to 0 km/h (0 mph) 7 times.
  4. Select Specific DTC.
  5. Enter DTC P0833.
Has the test run and passed?		 - Go to Step 18  Go to Step 2 
18 With the scan tool, observe the stored information, capture info and DTC info.
Does the scan tool display any DTCs that you have not diagnosed?		 - Go to Diagnostic Trouble Code (DTC) List - Vehicle System OK
scientia non olet · About LEMON Manuals