LEMON Manuals: Even more car manuals for everyone
Home >> Chevrolet >> 2006 >> Cobalt LTZ >> Repair and Diagnosis >> External Pages >> Different car >> Section 663 (Horn System) >> Diagnostic Information and Procedures >> DTC B2750 >> Test Description

Test Description

WARNING: This page is about a different car, the 2007 Pontiac G5 Pursuit, 2007 Pontiac G5, and 2007 Chevrolet Cobalt. However, it is still accessible from the selected car via links, so may be relevant.

The numbers below refer to the step numbers on the diagnostic table.

  1. 2:  During the horn relay operation, listen for an audible click. Command the ON and the OFF states. Repeat the commands as necessary.
  2. 3:  This step tests for voltage at the coil side of the horn relay. The horn fuse supplies power to the coil side of the horn relay.
  3. 4:  This step tests for a short to voltage in the horn relay signal circuit.
  4. 5:  This step verifies that the BCM is providing ground to the horn relay.
DTC B2750

Step Action Yes No
Schematic Reference: Horn Schematics 
Connector End View Reference: Horn Connector End Views 
1 Did you perform the Diagnostic System Check - Vehicle? Go to Step 2  Go to DIAGNOSTIC SYSTEM CHECK - VEHICLE
2 
  1. Turn ON the ignition, with the engine OFF.
  2. With a scan tool, command the horn relay ON and OFF.
Does the horn relay turn ON and OFF with each command?		 Go to Testing for Intermittent Conditions and Poor Connections Go to Step 3 
3 
  1. Turn OFF the ignition.
  2. Disconnect the horn relay.
  3. Turn ON the ignition, with the engine OFF.
  4. Probe the battery positive circuit of the horn with a test lamp connected to a good ground.
Does the test lamp illuminate?		 Go to Step 4  Go to Step 12 
4 
  1. Turn ON the ignition, with the engine OFF.
  2. Probe the horn relay control circuit of the horn relay with a test lamp connected to a good ground.
Does the test lamp illuminate?		 Go to Step 8  Go to Step 5 
5 
  1. Connect a test lamp between the control circuit of the horn relay and the battery positive voltage circuit of the horn relay.
  2. With a scan tool, command the horn relay ON and OFF.
Does the test lamp turn ON and OFF with each command?		 Go to Step 10  Go to Step 6 
6 Does the test lamp remain illuminated with each command? Go to Step 7  Go to Step 9 
7 Test the control circuit of the horn relay for a short to ground. Refer to Circuit Testing and Wiring Repairs .
Did you find and correct the condition?		 Go to Step 15  Go to Step 11 
8
  1. Turn ON the ignition, with the engine OFF.
  2. Test the control circuit of the horn relay for a short to voltage. Refer to Circuit Testing and Wiring Repairs .
Did you find and correct the condition?		 Go to Step 15  Go to Step 11 
9 Test the horn relay control circuit for an open. Refer to Circuit Testing and Wiring Repairs .
Did you find and correct the condition?		 Go to Step 15  Go to Step 11 
10 Inspect for poor connections at the horn relay. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs .
Did you find and correct the condition?		 Go to Step 15  Go to Step 11 
11 Inspect for poor connections at the harness connector of the body control module (BCM). Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs .
Did you find and correct the condition?		 Go to Step 15  Go to Step 11 
12 Repair the open in the horn relay battery positive voltage circuit. Refer to Wiring Repairs .
Did you complete the repair?		 Go to Step 15  -
13 Replace the horn relay.
Did you complete the replacement?		 Go to Step 15  -
14 Replace the BCM. Refer to Control Module References for replacement, setup, and programming.
Did you complete the replacement?		 Go to Step 15  -
15
  1. Use the scan tool in order to clear the DTCs.
  2. Operate the vehicle within the Conditions for Running the DTC.
Does the DTC reset?		 Go to Step 2  System OK
scientia non olet · About LEMON Manuals