LEMON Manuals: Even more car manuals for everyone
Home >> Chevrolet >> 2005 >> Aveo Base, 4D Hatchback >> Repair and Diagnosis >> External Pages >> Different car >> Section 28 (Automatic Transmission -- AISIN -- 81-40LE -- Diagnosis (DTC P0562 To DTC P0743)) >> Diagnosis >> DTC P0563 (Non Europe or N. American Emissions) >> Cause of Failure

Cause of Failure

WARNING: This page is about a different car, the 2004 Suzuki Swift + and 2004 Chevrolet Aveo. However, it is still accessible from the selected car via links, so may be relevant.
DTC P0563 (Non Europe or N. American Emissions)

Step Action Values Yes No
1
  1. Turn OFF the ignition.
  2. Install the scan tool.
  3. Turn ON the ignition, with the engine OFF.
  4. Run the engine to 600 RPM or greater.
  5. Record then clear the DTC(s).
  6. Select system voltage on the scan tool.
  7. Drive the vehicle and observe the scan tool for system voltage.
Is the voltage within the specified values?		 9-16 V Go to Step 4  Go to Step 2 
2
  1. Disconnect the battery cable.
  2. Measure the battery voltage.
Is the voltage within the specified values?		 9-16 V Go to Step 4  Go to Step 3 
3 Replace the battery.
Did you complete the replacement?		 - System OK -
4
  1. Turn ON the headlamp.
  2. Turn ON the air conditioner.
  3. Run the engine to 600 RPM or greater.
  4. Observe the scan tool for system voltage.
Is the voltage within the specified values?		 9-16 V Go to Step 6  Go to Step 5 
5
  1. Turn the ignition LOCK.
  2. Repair the alternator circuit, if necessary.
Did you complete the action?		 - System OK -
6 Test the EF7, F6 fuse for an open.
Was a problem found?		 - Go to Step 7  Go to Step 8 
7
  1. Test the EF7, F6 fuse for a short.
  2. Replace the fuse, if necessary.
Did you complete the replacement?		 - System OK -
8
  1. Turn ON the ignition.
  2. Measure the voltage of EF7, F6.
Is the voltage within the specified values?		 9-16 V Go to Step 10  Go to Step 9 
9 Repair the fuse voltage supply lines for open.
Did you complete the repair?		 - System OK -
10
  1. Turn the ignition LOCK.
  2. Disconnect the transmission control module (TCM) wiring connector.
  3. Measure the resistance between EF7 fuse and terminal A24 of the TCM wiring connector.
Is the resistance within the specified value?		 0 Ω Go to Step 12  Go to Step 11 
11 Repair the circuit between EF7 and terminal A24 for short to ground and open.
Did you complete the repair?		 - System OK -
12
  1. Disconnect the C204 connector and TCM connector.
  2. Turn ON the ignition.
  3. Measure the voltage of the terminal A24.
Is the voltage within the specified values?		 9-16 V Go to Step 13  Go to Step 14 
13 Repair the circuit from EF7 to terminal A24 of the TCM for short to battery.
Did you complete the repair?		 - System OK -
14
  1. Turn the ignition LOCK.
  2. Disconnect the C202 connector.
  3. Measure the resistance between F6 fuse and terminal A6 of the TCM wiring connector.
Is the resistance within the specified value?		 0 Ω Go to Step 16  Go to Step 15 
15 Repair the circuit between F6 and terminal A6 for short to ground and open.
Did you complete the repair?		 - System OK -
16
  1. Turn ON the ignition.
  2. Measure the voltage of the terminal A6.
Is the voltage within the specified values?		 9-16 V Go to Step 17  Go to Step 18 
17 Repair the circuit between F6 and terminal A6 for short to battery.
Did you complete the repair?		 - System OK -
18
  1. Inspect the transaxle wiring for poor electrical connectors at the transaxle connector.
  2. Look for possible bent, backed out, deformed, or damaged terminals.
  3. Check for weak terminal tension.
Was a condition found?		 - Go to Step 19  -
19 Replace the TCM. Refer to Transmission Control Module (TCM) Replacement .
Did you complete the replacement?		 - Go to Step 20  -
20
  1. After the repair, use a scan tool clear info function and road test the vehicle.
  2. Review the DTC info.
Has the last test failed or is the current DTC displayed?		 - Go to Step 1  System OK
scientia non olet · About LEMON Manuals