LEMON Manuals: Even more car manuals for everyone
Home >> Chevrolet >> 2004 >> Avalanche 2500 >> Repair and Diagnosis >> External Pages >> Different variant/trim >> Section 5 (Engine Control System - 4.8L, 5.3L & 6.0L (DTC P0452 To DTC P2120)) >> Diagnostic Information and Procedures >> DTC P0452 >> Test Description

Test Description

WARNING: This page is about a different variant/trim than selected.

The number below refers to the step number on the diagnostic table.

  1. 5:  This step tests for the proper operation of the circuit in the high voltage range.
DTC P0452

Step Action Value(s) Yes No
Schematic Reference:  Engine Controls Schematics 
Connector End View Reference:  Engine Controls Connector End Views  or  Powertrain Control Module (PCM) Connector End Views 
1 Did you perform the Diagnostic System Check-Engine Controls? - Go to Step 2  Go to Diagnostic System Check - Engine Controls
2
  1. Idle the engine for 1 minute.
  2. Monitor the diagnostic trouble code (DTC) information with a scan tool.
Did DTC P0641 or P0651 fail this ignition?		 - Go to Diagnostic Trouble Code (DTC) List Go to Step 3 
3 Observe the fuel tank pressure sensor parameter with the scan tool.
Does the scan tool indicate that fuel tank pressure sensor parameter is less than the specified value?		 0.1 V Go to Step 5  Go to Step 4 
4
  1. Observe the Freeze Frame/Failure Records for this DTC.
  2. Turn OFF the ignition for 30 seconds.
  3. Turn ON the ignition, with the engine OFF.
  4. Operate the vehicle within the Conditions for Running the DTC. You may also operate the vehicle within the conditions that you observed from the Freeze Frame/Failure Records.
Did the DTC fail this ignition?		 - Go to Step 5  Go to Intermittent Conditions
5 
  1. Turn OFF the ignition.
  2. Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle in General Information.
  3. Disconnect the fuel tank wiring harness at the fuel tank harness connector.
  4. Connect a 3-amp fused jumper wire between the 5-volt reference circuit of the FTP sensor and the signal circuit of the FTP sensor.
  5. Turn ON the ignition, with the engine OFF.
  6. Observe the fuel tank pressure sensor voltage with a scan tool.
Is the fuel tank pressure sensor parameter more than the specified value?		 4.8 V Go to Step 8  Go to Step 6 
6 Test the 5-volt reference circuit of the FTP sensor for an open between the fuel tank harness connector and the control module. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.
Did you find and correct the condition?		 - Go to Step 12  Go to Step 7 
7 Test the signal circuit of the FTP sensor for a short to ground, or an open between the fuel tank harness connector and the control module. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.
Did you find and correct the condition?		 - Go to Step 12  Go to Step 9 
8
  1. Remove the fuel tank. Refer to Fuel Tank Replacement (Single Tank) or Fuel Tank Replacement (Single Tank w/5.3L (L59) Engine) or Fuel Tank Replacement (Dual Tanks - Front) or Fuel Tank Replacement (Dual Tanks - Rear) .
  2. Inspect the fuel tank wiring harness for the following:
Did you find and correct the condition?		 - Go to Step 12  Go to Step 10 
9 Inspect for poor connections at the harness connector of the control module. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.
Did you find and correct the condition?		 - Go to Step 12  Go to Step 11 
10 Replace the FTP sensor. Refer to Fuel Tank Pressure Sensor Replacement (1500 Series) or Fuel Tank Pressure Sensor Replacement (2500 Series) .
Did you complete the replacement?		 - Go to Step 12  -
11 Replace the control module. Refer to Powertrain Control Module (PCM) Replacement .
Did you complete the replacement?		 - Go to Step 12  -
12
  1. Observe the Freeze Frame/Failure Records for this DTC.
  2. Turn OFF the ignition for 30 seconds.
  3. Turn ON the ignition, with the engine OFF.
  4. Operate the vehicle within the Conditions for Running the DTC. You may also operate the vehicle within the conditions that you observed from the Freeze Frame/Failure Records.
Did the DTC fail this ignition?		 - Go to Step 2  Go to Step 13 
13 Observe the Capture Info with a scan tool.
Are there any DTCs that have not been diagnosed?		 - Go to Diagnostic Trouble Code (DTC) List System OK
scientia non olet · About LEMON Manuals