LEMON Manuals: Even more car manuals for everyone
Home >> Chevrolet >> 2002 >> Blazer 4D Utility, 4WD, Part Time >> Repair and Diagnosis >> External Pages >> Different car >> Section 980 (Supplemental Inflatable Restraint System) >> Diagnostic Information and Procedures >> DTC B0090: Rollover Sensor Performance >> Test Description

Test Description

WARNING: This page is about a different car, the 2004 GMC Sierra, 2004 GMC Cab & Chassis Sierra, 2004 Chevrolet Silverado, and 2004 Chevrolet Cab & Chassis Silverado. However, it is still accessible from the selected car via links, so may be relevant.

The numbers below refer to the step numbers on the diagnostic table:

  1. 5:  Tests for an open or high resistance in the IP module disable switch power feed circuit.
  2. 6:  Tests for an open or high resistance in the IP module disable switch ground circuit.
  3. 8:  Tests for an open or high resistance in the IP module disable switch signal circuit.
  4. 9:  Tests for a short in the IP module disable switch signal circuit.
  5. 10:  Tests for short in the IP module suppression indicator control circuit.
  6. 11:  Tests for an open or high resistance in the IP module suppression indicator control circuit.
DTC B0090

Step Action Value(s) Yes No
Schematic Reference: SIR Schematics 
Connector End View Reference: SIR Connector End Views 
1 Did you perform the Diagnostic System Check - SIR? - Go to Step 2  Go to Diagnostic System Check - SIR 
2
  1. Turn OFF the ignition.
  2. Turn the IP module disable switch to the ON position.
  3. Turn ON the ignition, with the engine OFF.
Does the IP module disable switch ON indicator illuminate in the IP module disable switch?		 - Go to Step 7  Go to Step 3 
3
  1. Turn OFF the ignition.
  2. Disconnect the IP module disable switch connector. Refer to Inflatable Restraint Instrument Panel (I/P) Module Disable Switch Replacement .
  3. Inspect the IP module disable switch connector for corrosion or damage. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.
Did you find and correct the condition?		 - Go to Step 13  Go to Step 4 
4
  1. Disconnect the SDM connector. Refer to Inflatable Restraint Sensing and Diagnostic Module Replacement .
  2. Inspect the SDM connector for corrosion or damage. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.
Did you find and correct the condition?		 - Go to Step 13  Go to Step 5 
5  Test the IP module disable switch power feed circuit for an open or high resistance. Refer to Circuit Testing and Connector Repairs in Wiring Systems.
Did you find and correct the condition?		 - Go to Step 13  Go to Step 6 
6  Test the IP module disable switch ground circuit for an open or high resistance. Refer to Circuit Testing and Connector Repairs in Wiring Systems.
Did you find and correct the condition?		 - Go to Step 13  Go to Step 7 
7
  1. Install a scan tool.
  2. Turn the IP module disable switch to the ON position.
  3. Turn ON the ignition, with the engine OFF.
  4. With a scan tool, observe the SIR data list.
Does the IP module disable switch (active switch) show the specified state?		 Enabled Go to Step 9  Go to Step 8 
8 
  1. Turn OFF the ignition.
  2. Test the IP module disable switch signal circuit for an open or high resistance. Refer to Circuit Testing and Connector Repairs in Wiring Systems.
Did you find and correct the condition?		 - Go to Step 13  Go to Step 9 
9  Test the IP module disable switch signal circuit for a short. Refer to Circuit Testing and Connector Repairs in Wiring Systems.
Did you find and correct the condition?		 - Go to Step 13  Go to Step 10 
10  Test the IP module suppression indicator control circuit for a short. Refer to Circuit Testing and Connector Repairs in Wiring Systems.
Did you find and correct the condition?		 - Go to Step 13  Go to Step 11 
11  Test the IP module suppression indicator control circuit for an open or high resistance. Refer to Circuit Testing and Connector Repairs in Wiring Systems.
Did you find and correct the condition?		 - Go to Step 13  Go to Step 12 
12 Replace the IP module disable switch. Refer to Inflatable Restraint Instrument Panel (I/P) Module Disable Switch Replacement .
Did you complete the repair?		 - Go to Step 13  -
13
  1. Reconnect all SIR system components.
  2. Verify that all components, connectors and CPAs are properly mounted.
  3. Use the scan tool in order to clear the DTCs.
  4. Operate the vehicle within the Conditions for Running the DTC as specified in the supporting text.
Does the DTC reset?		 - Go to Step 2  System OK
scientia non olet · About LEMON Manuals