LEMON Manuals: Even more car manuals for everyone
Home >> Chevrolet >> 2002 >> Blazer 4D Utility, 4WD, Part Time >> Repair and Diagnosis >> External Pages >> Different car >> Section 94 (HVAC Systems - Automatic) >> Diagnostic Information and Procedures >> HVAC Compressor Clutch Does Not Disengage >> Test Description

Test Description

WARNING: This page is about a different car, the 2002 Oldsmobile Bravada, 2002 GMC Envoy XL, 2002 GMC Envoy, and 2002 Chevrolet TrailBlazer. However, it is still accessible from the selected car via links, so may be relevant.

The number below refers to the step number on the diagnostic table.

  1. 2:  These actions will disable the HVAC control module output to powertrain control module (PCM).
HVAC Compressor Clutch Does Not Disengage

Step Action Yes No
Schematic Reference: HVAC Schematics 
Connector End View Reference:  HVAC Connector End Views  
DEFINITION: The A/C compressor clutch will not disengage when an A/C request has not been made and a Powertrain DTC has not been set.
1 Did you perform the HVAC Diagnostic System Check? Go to Step 2  Go to Diagnostic System Check - HVAC Systems - Automatic 
2 
  1. Start the engine.
  2. Place the mode switch in the PANEL position.
  3. Place the A/C request switch in the OFF position.
Does the A/C compressor clutch engage?		 Go to Step 3  Go to TESTING FOR INTERMITTENT CONDITIONS AND POOR CONNECTIONS in Wiring Systems
3
  1. Turn OFF the ignition.
  2. Disconnect the A/C compressor clutch.
  3. Turn On the ignition, with the engine OFF.
  4. Probe the supply voltage circuit of the A/C compressor clutch with a test lamp that is connected to ground.
Does the test lamp illuminate?		 Go to Step 4  Go to Step 7 
4 Test the supply voltage circuit of the A/C compressor clutch for a short to voltage. Refer to CIRCUIT TESTING and WIRING REPAIRS in Wiring Systems.
Did you find and correct the condition?		 Go to Step 14  Go to Step 5 
5
  1. Turn OFF the ignition.
  2. Disconnect the A/C compressor clutch relay.
  3. Turn On the ignition, with the engine OFF.
  4. Connect a test lamp between the control circuit and the ignition-3 voltage circuit of the A/C compressor clutch relay.
Does the test lamp illuminate?		 Go to Step 6  Go to Step 8 
6 Test the control circuit of the A/C compressor clutch relay for a short to ground. Refer to CIRCUIT TESTING and WIRING REPAIRS in Wiring Systems.
Did you find and correct the condition?		 Go to Step 14  Go to Step 10 
7 Test the status signal circuit of the A/C compressor for a short to voltage. Refer to CIRCUIT TESTING and WIRING REPAIRS in Wiring Systems.
Did you find and correct the condition?		 Go to Step 14  Go to Step 9 
8 Inspect for poor connections at the A/C compressor clutch relay. Refer to TESTING FOR INTERMITTENT CONDITIONS AND POOR CONNECTIONS and CONNECTOR REPAIRS in Wiring Systems.
Did you find and correct the condition?		 Go to Step 14  Go to Step 11 
9 Inspect for poor connections at the harness connector of the A/C compressor clutch. Refer to TESTING FOR INTERMITTENT CONDITIONS AND POOR CONNECTIONS and CONNECTOR REPAIRS in Wiring Systems.
Did you find and correct the condition?		 Go to Step 14  Go to Step 12 
10 Inspect for poor connections at the harness connector of the powertrain control module (PCM). Refer to TESTING FOR INTERMITTENT CONDITIONS AND POOR CONNECTIONS and CONNECTOR REPAIRS in Wiring Systems.
Did you find and correct the condition?		 Go to Step 14  Go to Step 13 
11 Replace the A/C compressor clutch relay.
Did you complete the replacement?		 Go to Step 14  -
12 Replace the A/C compressor. Refer to COMPRESSOR REPLACEMENT (BODY TYPE VIN 3) in Heating, Ventilation and Air Conditioning.
Did you complete the replacement?		 Go to Step 14  -
13
IMPORTANT: Program the PCM.
Replace the PCM. Refer to POWERTRAIN CONTROL MODULE .Did you complete the replacement?		 Go to Step 14  -
14 Operate the system in order to verify the repair.
Did you correct the condition?		 System OK Go to Step 3 
scientia non olet · About LEMON Manuals