Conditions for Running the DTC

P013C

• DTCs P0050, P0056, P0059, P0060, P0101, P0102, P0103, P0106, P0107, P0108, P0120, P0121, P0122, P0123, P0151, P0152, P0153, P0154, P0155, P0157, P0158, P013C, P013D, P014A, P014B, P0160, P0161, P0174, P0175, P0201-P0206, P0220, P0222, P0223, P0300-P0306, P0442, P0443, P0446, P0449, P0455, P0496, P1153, P1175, P1516, P2101, P2119, P2135, P2176, P2272, P2273, P2A03 are not set.
• The system voltage is between 10-18 volts.
• The learned heater resistance is valid.
• The fuel level is more than 10 percent or the fuel level data fault is active.
• The engine run time is equal to or more than 60 seconds.

  THEN

• DFCO is active.
• The accelerator pedal position (APP) is stable.
• The torque converter clutch (TCC) is locked.
• DTCs P014A and P2272 have run and passed.
• This DTC runs once per trip.

P013D

• DTCs P0050, P0056, P0059, P0060, P0101, P0102, P0103, P0106, P0107, P0108, P0120, P0121, P0122, P0123, P0151, P0152, P0153, P0154, P0155, P0157, P0158, P013C, P013D, P014A, P014B, P0160, P0161, P0174, P0175, P0201-P0206, P0220, P0222, P0223, P0300-P0306, P0442, P0443, P0446, P0449, P0455, P0496, P1153, P1175, P1516, P2101, P2119, P2135, P2176, P2272, P2273, P2A03 are not set.
• The system voltage is between 10-18 volts.
• The learned heater resistance is valid.
• The fuel level is more than 10 percent, or the fuel level data fault is active.
• The engine run time is equal to or more than 60 seconds.

  THEN

• DTCs P013C, P014A, P014B, P2272 and P2273 have run and passed.
• This DTC runs once per trip.

P014A

• DTCs P0050, P0056, P0059, P0060, P0101, P0102, P0103, P0106, P0107, P0108, P0120, P0121, P0122, P0123, P0151, P0152, P0153, P0154, P0155, P0157, P0158, P013C, P013D, P014A, P014B, P0160, P0161, P0174, P0175, P0201-P0206, P0220, P0222, P0223, P0300-P0306, P0442, P0443, P0446, P0449, P0455, P0496, P1153, P1175, P1516, P2101, P2119, P2135, P2176, P2272, P2273, P2A03 are not set.
• The system voltage is between 10-18 volts.
• The learned heater resistance is valid.
• The fuel level is more than 10 percent, or the fuel level data fault is active.
• The engine run time is equal to or more than 40 seconds.

  THEN

• DFCO is active.
• The APP is stable.
• The TCC is locked.
• DTC P2272 has run and passed.
• This DTC runs once per trip.

P014B

• DTCs P0050, P0056, P0059, P0060, P0101, P0102, P0103, P0106, P0107, P0108, P0120, P0121, P0122, P0123, P0151, P0152, P0153, P0154, P0155, P0157, P0158, P013C, P013D, P014A, P014B, P0160, P0161, P0174, P0175, P0201-P0206, P0220, P0222, P0223, P0300-P0306, P0442, P0443, P0446, P0449, P0455, P0496, P1153, P1175, P1516, P2101, P2119, P2135, P2176, P2272, P2273, P2A03 are not set.
• The system voltage is between 10-18 volts.
• The learned heater resistance is valid.
• The fuel level is more than 10 percent, or the fuel level data fault is active.
• The engine run time is equal to or more than 40 seconds.

  THEN

• DTCs P013C, P014A, P2272 and P2273 have run and passed.
• This DTC runs once per trip.

P0153

• DTCs P0036, P0054, P0068, P0101, P0102, P0103, P0107, P0108, P0112, P0113, P0116, P0117, P0118, P0120, P0121, P0122, P0123, P0128, P0151, P0152, P0154, P0155, P0201, P0202, P0203, P0204, P0205, P0206, P0220, P0222, P0223, P0300, P0442, P0443, P0446, P0449, P0451, P0452, P0454, P0455, P0496, P1516, P2101, P2119, P2135, P2176 are not set.
• The system voltage is between 10-18 volts.
• The scan tool special functions are not active.
• The HO2S Bank 2 Sensor 1 Heater command parameter is ON.
• The ECT sensor parameter is more than 65°C (149°F).
• The Engine Run Time parameter is more than 60 seconds.
• The vehicle is not in Park, Reverse, or Neutral.
• The Loop Status parameter is closed.
• The mass air flow (MAF) sensor parameter is between 15-37 g/s.
• The TP Indicated Angle parameter is more than 3.5 percent.
• The Engine Speed parameter is between 1,250-2,550 RPM.
• The evaporative emission (EVAP) system is purging.
• The Barometric Pressure (BARO) parameter is at least 69.8 kPa.
• The above conditions have been met for one second.

P0154

• DTCs P0068, P0101, P0102, P0103, P0107, P0108, P0112, P0113, P0116, P0117, P0118, P0120, P0121, P0122, P0123, P0128, P0201, P0202, P0203, P0204, P0205, P0206, P0220, P0222, P0223, P0442, P0443, P0446, P0449, P0451, P0452, P0453, P0454, P0455, P0496, P1516, P2101, P2119, P2135, P2176 are not set.
• The system voltage is between 10-18 volts.
• The scan tool special functions are not active.
• The HO2S Bank 2 Sensor 1 Heater command parameter is ON.
• The Engine Run time parameter is more than 2 minutes.

P0160 - Regular Test

• DTCs P0056, P0060, P0068, P0101, P0102, P0103, P0107, P0108, P0112, P0113, P0116, P0117, P0118, P0120, P0121, P0122, P0123, P0128, P0141, P0201, P0202, P0203, P0204, P0205, P0206, P0220, P0222, P0223, P0442, P0443, P0446, P0449, P0451, P0452, P0453, P0454, P0455, P0496, P1516, P2101, P2119, P2135, P2176 are not set.
• The system voltage is between 10-18 volts.
• The scan tool special functions are not active.
• The Engine Run Time parameter is more than 2 minutes.
• The TP Indicated Angle parameter has changed more than 3 percent at least 1 time.
• The Loop Status parameter is closed.
• The predicted HO2S temperature is more than 0°C (32°F).

P0160 - Fast Pass Test

• DTCs P0056, P0060, P0068, P0101, P0102, P0103, P0107, P0108, P0112, P0113, P0116, P0117, P0118, P0120, P0121, P0122, P0123, P0128, P0141, P0201, P0202, P0203, P0204, P0205, P0206, P0220, P0222, P0223, P0442, P0443, P0446, P0449, P0451, P0452, P0453, P0454, P0455, P0496, P1516, P2101, P2135, P2176 are not set.
• The system voltage is between 10-18 volts.
• The scan tool special functions are not active.
• The Engine Run Time parameter is less than 90 seconds.

P1153

• DTCs P0050, P0059, P0068, P0101, P0102, P0103, P0107, P0108, P0112, P0113, P0116, P0117, P0118, P0120, P0121, P0122, P0123, P0128, P0151, P0152, P0154, P0155, P0201, P0202, P0203, P0204, P0205, P0206, P0220, P0222, P0223, P0300, P0442, P0443, P0446, P0449, P0451, P0452, P0454, P0455, P0496, P1516, P2101, P2119, P2135, P2176, P2A03 are not set.
• The system voltage is between 10-18 volts.
• The scan tool special functions are not active.
• The HO2S Bank 2 Sensor 1 Heater command parameter is ON.
• The ECT Sensor parameter is more than 65°C (149°F).
• The Engine Run Time parameter is at least 60 seconds.
• The EVAP purge solenoid is commanded ON.
• The MAF sensor parameter is between 15-37 g/s.
• The Engine Speed parameter is between 1,250-2,550 RPM.
• The TP Indicated Angle parameter is greater than 3.5 percent.
• The Loop Status parameter is closed.
• The BARO parameter is at least 69.8 kPa.
• The vehicle is not in Park, Reverse, or Neutral.
• The above conditions have been met for one second.

P2272

1. Condition 1
   • DTCs P0050, P0059, P0068, P0101, P0102, P0103, P0107, P0108, P0112, P0113, P0117, P0118, P0120, P0121, P0122, P0123, P0128, P0151, P0152, P0153, P0154, P0155, P0171, P0172, P0174, P0175, P0201, P0202, P0203, P0204, P0205, P0206, P0220, P0222, P0223, P0442, P0443, P0446, P0449, P0451, P0452, P0453, P0454, P0455, P0496, P1153, P1516, P2101, P2119, P2135, P2176, P2273, P2A03 are not set.
   • The system voltage is between 10-18 volts.
   • The learned heater resistance is valid.
   • The fuel level is more than 10 percent, or the fuel level data fault is active.
   • The engine run time is equal to or more than 40 seconds.
2. Condition 2
   • The engine speed is between 1,100-2,100 RPM.
   • The airflow is equal to or more than 3 g/s, and equal to or less than 12 g/s.
   • The vehicle speed is equal to or more than 73 km/h (45.4 mph), and equal to or less than 120 km/h (74.6 mph).
   • The short term fuel trim is equal to or more than 0.9, and equal to or less than 1.065.
   • The fuel state is in Closed Loop.
   • The EVAP diagnostics are not in control of purge.
   • The post cell is enabled.
   • The EGR diagnostic is not intrusive.
   • The heater warm-up delay is more than 120 seconds.
   • The catalytic converter temperature is equal to or more that 650°C (1,202°F), and equal to less than 900°C (1,652°F).
   • This DTC runs once per trip when all of the above conditions have been met for 2 seconds.

P2273

1. Condition 1
   • DTCs P0050, P0059, P0068, P0101, P0102, P0103, P0107, P0108, P0112, P0113, P0117, P0118, P0120, P0121, P0122, P0123, P0128, P0151, P0152, P0153, P0154, P0155, P0171, P0172, P0174, P0175, P0201, P0202, P0203, P0204, P0205, P0206, P0220, P0222, P0223, P0442, P0443, P0446, P0449, P0451, P0452, P0453, P0454, P0455, P0496, P1153, P1516, P2101, P2119, P2135, P2176, P2272, or P2A03 are not set.
   • The system voltage is between 10-18 volts.
   • The learned heater resistance is valid.
   • The fuel level is more than 10 percent, or the fuel level data fault is active.
   • The engine run time is equal to or more than 40 seconds.
2. Condition 2
   • DFCO is active.
   • The accelerator pedal (APP) is stable.
   • The torque converter clutch (TCC) is locked.
   • DTC P2270 has run and passed.
   • This DTC runs once per trip.

P2A03

• DTCs P0050, P0059, P0068, P0101, P0102, P0103, P0107, P0108, P0112, P0113, P0117, P0118, P0120, P0121, P0122, P0123, P0128, P0131, P0132, P0133, P0134, P0151, P0152, P0153, P0154, P0155, P0201, P0202, P0203, P0204, P0205, P0206, P0220, P0222, P0223, P0442, P0443, P0446, P0449, P0451, P0452, P0453, P0454, P0455, P0496, P1133, P1153, P1516, P2101, P2119, P2135, P2176, P2272, P2273 are not set.
• The Engine Run Time parameter is more than 100 seconds.
• The MAF Sensor parameter is between 5-37 g/s.
• The Engine Speed parameter is between 500-3,000 RPM.
• The ECT Sensor parameter is more than 75°C (167°F).
• The ignition 1 signal parameter is between 10-18 volts.
• DTC P2A03 runs continuously when the above conditions are met for 5 seconds.