LEMON Manuals: Even more car manuals for everyone
Home >> Chevrolet >> 2002 >> Blazer 4D Utility, 4WD, Part Time >> Repair and Diagnosis >> External Pages >> Different car >> Section 1893 (Drive Axles - Front) >> Repair Instructions >> Inner Axle Seal And/Or Bearing Replacement - Front Drive Axle >> Removal Procedure

Removal Procedure

WARNING: This page does not describe the selected car, but rather 9 other vehicles, including the 2002 GMC Yukon XL, 2002 GMC Yukon, 2002 GMC Sierra, 2002 Chevrolet Tahoe, and 2002 Chevrolet Suburban. However, it is still accessible from the selected car via links, so may be relevant.
  1. Raise the vehicle. Refer to LIFTING & JACKING THE VEHICLE .
  2. Drain the differential carrier assembly. Refer to LUBRICANT REPLACEMENT - FRONT DRIVE AXLE .
  3. If replacing the right side seal and/or bearing, perform the following steps:
    1. Remove the inner axle shaft and housing assembly from the differential carrier case assembly. Refer to INNER SHAFT AND/OR HOUSING REPLACEMENT - FRONT DRIVE AXLE (8.25 S4WD AND 9.25 AXLES)  or INNER SHAFT AND/OR HOUSING REPLACEMENT - FRONT DRIVE AXLE (8.25 F4WD AXLE) .
    2. Remove the clutch fork assembly components and the inner axle shaft from the inner axle shaft housing. Refer to INNER SHAFT AND/OR HOUSING REPLACEMENT - FRONT DRIVE AXLE (8.25 S4WD AND 9.25 AXLES)  or INNER SHAFT AND/OR HOUSING REPLACEMENT - FRONT DRIVE AXLE (8.25 F4WD AXLE) 
    3. Install the inner axle shaft housing into a vise.

      Clamp only on the mounting flange of the inner axle shaft housing.

    4. Install the J 29369-1  , 8.25 inch axle, or the J 29369-2  , 9.25 inch axle, behind the inner axle shaft seal or the inner axle shaft bearing as necessary.
    5. Install the J 2619-01  (2) to the J 29369-1  or the J 29369-2  (1).
      Fig 1: Installing Slide Hammer To Bushing And Bearing Remover
      G01455850Courtesy of GENERAL MOTORS CORP.
    6. Remove the inner axle shaft seal and/or the inner axle shaft bearing using the J 2619-01  .
  4. If only replacing the left side seal, perform the following steps:
    1. Place an alignment mark between the inner axle shaft and the wheel drive shaft.
    2. Disconnect the wheel drive shaft from the inner axle shaft.
    3. Remove the inner axle shaft using a hammer and a brass drift.
    4. Remove the inner axle shaft seal using a suitable seal remover tool.
    Fig 2: Removing Inner Axle Shaft Seal/Bearing
    GM1332786
  5. If replacing the left side seal and/or bearing, perform the following steps:
    1. Remove the differential carrier assembly. Refer to DIFFERENTIAL CARRIER ASSEMBLY REPLACEMENT .
    2. Place the differential carrier assembly into a vise.

      Clamp only on the mounting flange of the differential carrier assembly case.

    3. Remove the inner axle shaft using a hammer and a brass drift.
    4. Install the J 29369-1  , 8.25 inch axle, or the J 29369-2  , 9.25 inch axle, behind the inner axle shaft seal or the inner axle shaft bearing as necessary.
      Fig 3: Removing Inner Axle Shaft Seal/Bearing
      GM1332786
    5. Install the J 2619-01  to the J 29369-1  or the J 29369-2  .
    6. Remove the inner axle shaft seal and/or the inner axle shaft bearing using the J 2619-01  .
scientia non olet · About LEMON Manuals