LEMON Manuals: Even more car manuals for everyone
Home >> Chevrolet >> 2002 >> Blazer 4D Utility, 4WD, Part Time >> Repair and Diagnosis >> External Pages >> Different car >> Section 1867 (Automatic Transaxle - 4T45-E - DTC P0719 To DTC P0842) >> DTC P0719 (2.2L) >> Test Description

Test Description

WARNING: This page is about a different car, the 2007 Saturn Vue. However, it is still accessible from the selected car via links, so may be relevant.

The numbers below refer to the step numbers on the diagnostic table.

  1. 2:  Disconnecting the stop lamp switch connector, jumping the circuit, and observing a status change, isolates the stop lamp switch as the source of the DTC.
  2. 3:  If the ignition 1 voltage circuit shorts to ground, the BRAKE fuse opens.
  3. 5:  If the stop lamp switch is properly adjusted, then the stop lamp switch must be replaced.
  4. 8:  Replace the TCM only after you have completed the preceding diagnostic steps.
DTC P0719 (2.2L)

Step Action Yes No
1 Did you perform the Diagnostic System Check - Vehicle? Go to Step 2  Go to Diagnostic System Check - Vehicle
2 
  1. Install a scan tool.
  2. Turn ON the ignition, with the engine OFF.
    3. IMPORTANT: Before clearing the DTC, use the scan tool in order to record the Failure Records. Using the Clear Info function erases the Failure Records from the TCM.
  3. Record the DTC Failure Records.
  4. Clear the DTC.
  5. Select Brake Switch on the scan tool.
  6. Disconnect the stop lamp switch connector.
  7. Using the J-35616  connector test adapter kit, install a fused jumper wire between the ignition 1 voltage and the stop lamp switch signal circuits of the stop lamp switch connector.
Did the Brake Switch status change from Open to Closed?		 Go to Step 5  Go to Step 3 
3 
  1. Remove the BRAKE fuse.
  2. Inspect the fuse for an open. Refer to Circuit Protection - Fuses .
Is the fuse open?		 Go to Step 4  Go to Step 6 
4
IMPORTANT: The condition that affects this circuit may exist in other connecting branches of the circuit. Refer to Power Distribution Schematics for complete circuit distribution.
Test the ignition 1 voltage circuit of the stop lamp switch for a short to a ground. Refer to Testing for Short to Ground and Wiring Repairs .Did you find and correct the condition?		 Go to Step 9  -
5 
  1. Inspect the stop lamp switch for proper adjustment.
  2. Adjust the stop lamp switch as necessary. Refer to Stop Lamp Switch Adjustment .
Did the stop lamp switch require adjustment?		 Go to Step 9  Go to Step 7 
6
  1. Test the ignition 1 voltage circuit of the stop lamp switch for an open.
  2. Test the signal circuit of the stop lamp switch for an open.
Refer to Testing for Continuity and Wiring Repairs .Did you find and correct a condition?		 Go to Step 9  Go to Step 8 
7 Replace the stop lamp switch. Refer to Stop Lamp Switch Replacement .
Did you complete the replacement?		 Go to Step 9  -
8  Replace the TCM. Refer to Control Module References for replacement, setup, and programming.
Did you complete the replacement?		 Go to Step 9  -
9 Perform the following procedure in order to verify the repair:
  1. Select DTC.
  2. Select Clear Info.
  3. Operate the vehicle under the following conditions:
    • Turn ON the ignition, with the engine OFF.
    • Apply and release the brake pedal.
    • The TCM must receive 12 volts, stop lamp switch closed, on the circuit for 5 seconds.
  4. Select Specific DTC.
  5. Enter DTC P0719.

Has the test run and passed?		 Go to Step 10  Go to Step 2 
10 With the scan tool, observe the stored information, capture info and DTC info.
Does the scan tool display any DTCs that you have not diagnosed?		 Go to Diagnostic Trouble Code (DTC) List - Vehicle System OK
scientia non olet · About LEMON Manuals