Conditions for Clearing the MIL/DTC

WARNING: This page is about a different car, the 2007 Saturn Vue. However, it is still accessible from the selected car via links, so may be relevant.

The control module turns OFF the malfunction indicator lamp (MIL) after 3 consecutive ignition cycles that the diagnostic runs and does not fail.
A current DTC, Last Test Failed, clears when the diagnostic runs and passes.
A history DTC clears after 40 consecutive warm-up cycles, if no failures are reported by this or any other emission related diagnostic.
Clear the MIL and the DTC with a scan tool.

DTC P0107

Step	Action	Values	Yes	No
Schematic Reference: Engine Controls Schematics Connector End View Reference: Engine Controls Connector End Views or Engine Control Module Connector End Views
1	Did you perform the Diagnostic System Check - Vehicle?	-	Go to Step 2	Go to Diagnostic System Check - Vehicle
2	Start the engine. Monitor the DTC Information with the scan tool. Is DTC P0651 also set?	-	Go to DTC P0651	Go to Step 3
3	Observe the manifold absolute pressure (MAP) sensor parameter with the scan tool. Is the voltage is less than the specified value?	0.1 V	Go to Step 5	Go to Step 4
4	Observe the Freeze Frame/Failure Records for this DTC. Turn OFF the ignition for 30 seconds. Start the engine. Operate the vehicle within the Conditions for Running the DTC. You may also operate the vehicle within the conditions that you observed from the Freeze Frame/Failure Records. Does the DTC fail this ignition?	-	Go to Step 5	Go to Testing for Intermittent Conditions and Poor Connections
5	Test for an intermittent and for a poor connection at the MAP sensor. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs . Did you find and correct the condition?	-	Go to Step 13	Go to Step 6
6	Turn OFF the ignition. Disconnect the MAP sensor electrical connector. Turn ON the ignition, with the engine OFF. Measure the voltage from the 5-volt reference circuit of the MAP sensor to a good ground, with a DMM. Is the voltage more than the specified value?	4.8 V	Go to Step 7	Go to Step 8
7	Connect a 3-amp fused jumper wire between the 5-volt reference circuit of the MAP sensor and the signal circuit of the MAP sensor. Observe the MAP sensor parameter with the scan tool. Is the voltage more than the specified value?	4.9 V	Go to Step 11	Go to Step 9
8	Test the 5-volt reference circuit between the engine control module (ECM) and the MAP sensor for an open. Refer to Circuit Testing and Wiring Repairs . Did you find and correct the condition?	-	Go to Step 13	Go to Step 10
9	Test the MAP sensor signal circuit between the ECM and the MAP sensor for a short to ground or an open. Refer to Circuit Testing and Wiring Repairs . Did you find and correct the condition?	-	Go to Step 13	Go to Step 10
10	Test for an intermittent and for a poor connection at the ECM. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs . Did you find and correct the condition?	-	Go to Step 13	Go to Step 12
11	Replace the MAP sensor. Refer to Manifold Absolute Pressure Sensor Replacement . Did you complete the replacement?	-	Go to Step 13	-
12	Replace the ECM. Refer to Control Module References for replacement, setup, and programming. Did you complete the replacement?	-	Go to Step 13	-
13	Clear the DTCs with a scan tool. Turn OFF the ignition for 30 seconds. Start the engine. Operate the vehicle within the Conditions for Running the DTC. You may also operate the vehicle within the conditions that you observed from the Freeze Frame/Failure Records. Did the DTC fail this ignition?	-	Go to Step 2	Go to Step 14
14	Observe the Capture Info with a scan tool. Are there any DTCs that have not been diagnosed?	-	Go to Diagnostic Trouble Code (DTC) List - Vehicle	System OK