LEMON Manuals: Even more car manuals for everyone
Home >> Chevrolet >> 2002 >> Blazer 4D Utility, 4WD, Part Time >> Repair and Diagnosis >> External Pages >> Different car >> Section 1650 (Retained Accessory Power System) >> Diagnostic Information and Procedures >> Retained Accessory Power (RAP) Inoperative (with relay)

Retained Accessory Power (RAP) Inoperative (with relay)

WARNING: This page is about a different car, the 2002 Oldsmobile Bravada, 2002 GMC Envoy XL, 2002 GMC Envoy, and 2002 Chevrolet TrailBlazer. However, it is still accessible from the selected car via links, so may be relevant.
Retained Accessory Power (RAP) Inoperative (with relay)

Step Action Yes No
Schematic Reference: MASTER ELECTRICAL COMPONENT LIST in Wiring Systems
1 Did you perform the retained accessory power (RAP) diagnostic system check? Go to Step 2  Go to Diagnostic System Check - Retained Accessory Power 
2 Test the following circuits of the bodycontrol module (BCM) for an open or a short to ground:
  • Battery Input Voltage
  • Battery Output voltage
  • Ignition input voltage
  • Ignition output voltage

Refer to the following:
Did you find and correct condition?		 Go to Step 13  Go to Step 3 
3
  1. Connect a scan tool.
  2. With the scan tool, observe all door jamb/liftgate switches.
  3. Open and close each door.
Does the scan tool display change from active to inactive?		 Go to Step 4  Go to DIAGNOSTIC SYSTEM CHECK - LIGHTING SYSTEMS in Lighting Systems
4 Enable RAP power mode.
The radio should operate during the RAP power mode via a class 2 signal from the BCM.
Does the radio operate during the 10 minute RAP time period?		 Go to Step 5  Go to Step 11 
5 With RAP power mode enabled, test for battery voltage at the control circuit of the RAP relay. Refer to CIRCUIT TESTING and WIRING REPAIRS in Wiring Systems.
Is battery voltage present?		 Go to Step 6  Go to Step 8 
6 Test for battery voltage at the supply side of the RAP relay contacts.
Did you locate and repair the fault?		 Go to Step 13  Go to Step 7 
7 With RAP power mode enabled, test for a battery voltage supply output, after the relay. Refer to CIRCUIT TESTING and WIRING REPAIRS in Wiring Systems.
Did you locate and repair the fault?		 Go to Step 13  Go to Step 10 
8
IMPORTANT: If the BCM has no output at the RAP control terminal test the complete external circuit for a short to ground before replacing parts.
  1. Remove the terminal from the BCM harness connector that contains the RAP relay control circuit.
  2. Enable RAP Power Mode.
  3. Test the RAP relay control circuit at the BCM for voltage.
Is there voltage at the RAP control output on the BCM?		 Go to Step 9  Go to Step 11 
9 Test for a short to ground or an open circuit in the RAP relay control circuit from the BCM to the RAP relay socket. Refer to CIRCUIT TESTING and WIRING REPAIRS in Wiring Systems.
Did you find and correct the condition?		 Go to Step 13  Go to Step 10 
10 Replace the RAP relay.
Is the replacement complete?		 Go to Step 13  -
11 Inspect for poor connections or terminal damage at the BCM. Refer to TESTING FOR INTERMITTENT CONDITIONS AND POOR CONNECTIONS and CONNECTOR REPAIRS and in Wiring Systems.
Did you find and correct the condition?		 Go to Step 13  Go to Step 12 
12
IMPORTANT: Setup and Reprogram the module
Replace the BCM. Refer to BODY CONTROL MODULE REPLACEMENT in Body Control System.Did you complete the replacement?		 Go to Step 13  -
13 Enable RAP power mode to verify the repair.
Did you correct the condition?		 System OK Go to Step 1 
scientia non olet · About LEMON Manuals