LEMON Manuals: Even more car manuals for everyone
Home >> Chevrolet >> 2002 >> Blazer 4D Utility, 4WD, Part Time >> Repair and Diagnosis >> External Pages >> Different car >> Section 1571 (Power Seat System) >> Diagnostic Information and Procedures >> DTC B1825, B1850, B1860, B2355, B2365, or B2375 >> Diagnostic Aids

Diagnostic Aids

WARNING: This page is about a different car, the 2002 Oldsmobile Bravada, 2002 GMC Envoy XL, 2002 GMC Envoy, and 2002 Chevrolet TrailBlazer. However, it is still accessible from the selected car via links, so may be relevant.

If the DTC is only found in history, the fault may be intermittent. Refer to TESTING FOR INTERMITTENT CONDITIONS AND POOR CONNECTIONS in Wiring Systems.

DTC B1825, B1850, B1860, B2355, B2365, or B2375

Step Action Values Yes No
Schematic Reference:  Memory Seats Schematics  
Connector End View Reference:  Power Seat Systems Connector End Views  
1 Did you perform the Power Seat Diagnostic System Check? - Go to Step 2  Go to Diagnostic System Check - Power Seat Systems 
2
  1. Install a scan tool.
  2. With a scan tool, observe the appropriate Position Sensor parameter in the seat module Sensor Data list.
Is the Position Sensor parameter is within the specified range?		 0.39-4.58 V Go to TESTING FOR INTERMITTENT CONDITIONS AND POOR CONNECTIONS in Wiring Systems Go to Step 3 
3
  1. Disconnect the position sensor connector.
  2. With a scan tool, observe the Position Sensor parameter.
Is the Position Sensor parameter less than the specified value?		 0.39 V Go to Step 4  Go to Step 8 
4
  1. Connect a 3 amp fused jumper wire between the 5 volt reference circuit of the position sensor and the signal circuit of the position sensor.
  2. With a scan tool, observe the Position Sensor parameter.
Is the Position Sensor parameter is greater than the specified value?		 4.58 V Go to Step 5  Go to Step 7 
5
  1. Disconnect the fused jumper wire.
  2. Measure the voltage between the 5-volt reference circuit of the seat sensor and the low reference circuit of the seat sensor.
Is the voltage measure greater than the specified value?		 5.0 V Go to Step 6  Go to Step 10 
6 Test the 5-volt reference circuit for a short to voltage. Refer to CIRCUIT TESTING and WIRING REPAIRS in Wiring Systems.
Did you find and correct the condition?		 - Go to Step 15  Go to Step 12 
7 Test the 5-volt reference circuit for one of the following conditions:
  • A short to ground
  • A high resistance
  • An open

Refer to CIRCUIT TESTING and WIRING REPAIRS in Wiring Systems.
Did you find and correct the condition?		 - Go to Step 15  Go to Step 9 
8 Test the signal circuit of the position sensor for a short to voltage. Refer to CIRCUIT TESTING and WIRING REPAIRS in Wiring Systems.
Did you find and correct the condition?		 - Go to Step 15  Go to Step 12 
9 Test the signal circuit of the position sensor for one of the following conditions:
  • A short to ground
  • A high resistance
  • An open

Refer to CIRCUIT TESTING and WIRING REPAIRS in Wiring Systems.
Did you find and correct the condition?		 - Go to Step 15  Go to Step 12 
10 Test the low reference circuit of the position sensor for an open or high resistance. Refer to CIRCUIT TESTING and WIRING REPAIRS in Wiring Systems.
Did you find and correct the condition?		 - Go to Step 15  Go to Step 11 
11 Inspect for poor connections at the position sensor. Refer to TESTING FOR INTERMITTENT CONDITIONS AND POOR CONNECTIONS and CONNECTOR REPAIRS in Wiring Systems.
Did you find and correct the condition?		 - Go to Step 15  Go to Step 13 
12 Inspect for poor connections at the seat control module. Refer to TESTING FOR INTERMITTENT CONDITIONS AND POOR CONNECTIONS and CONNECTOR REPAIRS in Wiring Systems.
Did you find and correct the condition?		 - Go to Step 15  Go to Step 14 
13 Replace the seat sensor. Refer to Seat Adjuster Mechanism Replacement - Power .
Did you complete the replacement?		 - Go to Step 15  -
14 Replace the Seat Module. Refer to Memory Seat Control Module Replacement .
Did you complete the replacement?		 - Go to Step 15  -
15
  1. Use the scan tool in order to clear the DTCs.
  2. Operate the vehicle within the Conditions for Running the DTC as specified in the supporting text.
Does the DTC reset?		 - Go to Step 2  System OK
scientia non olet · About LEMON Manuals