LEMON Manuals: Even more car manuals for everyone
Home >> Chevrolet >> 2002 >> Blazer 4D Utility, 4WD, Part Time >> Repair and Diagnosis >> External Pages >> Different car >> Section 1541 (Seat Belt System) >> Repair Instructions >> Seat Belt Retractor Anchor Plate Replacement (Convertible) >> Installation Procedure

Installation Procedure

WARNING: This page is about a different car, the 2004 Chevrolet Corvette. However, it is still accessible from the selected car via links, so may be relevant.
    Fig 1: Seat Belt Anchor Plate & Stiff Wire
    GM484096Courtesy of GENERAL MOTORS CORP.
  1. Remove the folding top stowage lid bumper from the top of the lock pillar.
  2. Route a long stiff wire down through the bumper hole and out through the drilled out hole.
  3. Attach a new seat belt anchor plate to the stiff wire.
    1. Insert the wire through the threaded hole in the anchor plate.
    2. Slide the plate up the wire.
    3. Make a small loop in the wire so the anchor plate can not side back down the wire.
    4. Fig 2: Pulling The Stiff Wire With Anchor Plate Through Drilled Out Hole Upward Where Plate Attaches
    GM483968Courtesy of GENERAL MOTORS CORP.
  4. Pull the stiff wire with the anchor plate attached through the drilled out hole upward to the hole where the plate attaches.
  5. Insert a hooked rod through the bolt hole in the pillar and hook the anchor plate.
    6. Fig 3: Anchor Plate, Lock Pillar & Stiff Wire
    GM483971Courtesy of GENERAL MOTORS CORP.
  6. Pull the anchor plate into position against the inside of the lock pillar.
  7. Push the stiff wire down and remove the stiff wire through the drilled hole.
  8. Pull the anchor plate into position tight against the inside of the lock pillar.
    9. CAUTION: To avoid personal injury when exposed to welding flashes or to galvanized (Zinc Oxide) metal toxic fumes while grinding/cutting on any type of metal or sheet molded compound, you must work in a properly ventilated area, wearing an approved respirator, eye protection, earplugs, welding gloves, and protective clothing.
  9. Mig weld the anchor plate into position welding both ends of the anchor plate to the pillar.
  10. Remove the hooked rod.
    11. Fig 4: Grind Welded Surface
    GM483972Courtesy of GENERAL MOTORS CORP.
  11. Grind smooth the welded surface.
    12. Fig 5: Primer Repaired Area
    GM483975Courtesy of GENERAL MOTORS CORP.
  12. Apply primer to the repaired area.
    13. Fig 6: Cover Drilled Hole With Sealing Patch
    GM280290Courtesy of GENERAL MOTORS CORP.
  13. Cover the drilled hole (1) with a sealing patch.
    14. Fig 7: Seat Belt Guide Bracket Stud & Upper Guide
    GM213980Courtesy of GENERAL MOTORS CORP.
  14. Remove the protective cover from the interior of the vehicle.
    15. NOTE: Refer to Fastener Notice in Cautions and Notices.
  15. Reposition the ground wires and install the ground bolt.

    Tighten:  Tighten the antenna ground bolt to 5.8 N.m (51 lb in).

  16. Reposition the wire harness.
  17. Install the intermediate carpet.
  18. Install the lock pillar lower trim. Refer to Trim Replacement - Lock Pillar (Upper Convertible) or Trim Replacement - Lock Pillar (Coupe) or Trim Replacement - Lock Pillar (Lower Convertible and Hard Top) in Interior Trim.
  19. Install the lock pillar upper trim. Refer to Trim Replacement - Lock Pillar (Upper Convertible) or Trim Replacement - Lock Pillar (Coupe) or Trim Replacement - Lock Pillar (Lower Convertible and Hard Top) in Interior Trim.
  20. Install the stowage lid bumper.
  21. Install the seat. Refer to Seat Replacement (Power) or Seat Replacement (Manual) (Power) or Seat Replacement (Power) or Seat Replacement (Manual) (Manual) in Seats.
  22. Raise and secure the folding top.
scientia non olet · About LEMON Manuals