LEMON Manuals: Even more car manuals for everyone
Home >> Chevrolet >> 2002 >> Blazer 4D Utility, 4WD, Part Time >> Repair and Diagnosis >> External Pages >> Different car >> Section 1518 (Interior Trim) >> Repair Instructions >> Folding Top Headliner Replacement >> Installation Procedure

Installation Procedure

WARNING: This page is about a different car, the 2004 Chevrolet Corvette. However, it is still accessible from the selected car via links, so may be relevant.
    CAUTION: Do not attempt to repair or alter the head impact energy-absorbing material glued to the headliner or to the garnish trims. If the material is damaged, replace the headliner and/or the garnish trim. Failure to do so could result in personal injury.
  1. Install the headliner retainer to the #3 bow.
    2. Fig 1: Headliner Retainer Screws To #3 Bow
    GM784514Courtesy of GENERAL MOTORS CORP.
    NOTE: Refer to Fastener Notice in Cautions and Notices.
  2. Install the headliner retainer screws to the #3 bow.

    Tighten:  Tighten the screws to 2 N.m (18 lb in).

  3. Install the headliner retainer screws to the #4 bow.

    Tighten:  Tighten the screws to 2 N.m (18 lb in).

    4. Fig 2: Headliner Retainer Screws To #4 Bow
    GM784512Courtesy of GENERAL MOTORS CORP.
  4. Install the support strap screws for the rear window to the #4 bow.

    Tighten:  Tighten the screws to 2 N.m (18 lb in).

  5. Install the retainer screws for the headliner elastic strap to the rear side rails.

    Tighten:  Tighten the screws to 2 N.m (18 lb in).

  6. Install the headliner screws to the rear side rails.

    Tighten:  Tighten the screws to 2 N.m (18 lb in).

  7. Install the retainers screws for the headliner elastic strap to the #5 bow.

    Tighten:  Tighten the screws to 2 N.m (18 lb in).

    8. Fig 3: Folding Top With The #1 Bow And The #5 Bow Up
    GM289910Courtesy of GENERAL MOTORS CORP.
  8. Position the #1 and #5 bow up.
    9. Fig 4: Headliner Retainer Screws To #2 Bow
    GM784505Courtesy of GENERAL MOTORS CORP.
  9. Install the headliner retainer screws to the #2 bow.

    Tighten:  Tighten the to 2 N.m (18 lb in).

    10. Fig 5: Headliner Extension Push-On Retainers At Studs To #1 Bow
    GM784499Courtesy of GENERAL MOTORS CORP.
  10. Install the headliner extension push-on retainers to the #1 bow stud.
    11. Fig 6: Headliner Side Screws To #1 Bow
    GM784498Courtesy of GENERAL MOTORS CORP.
  11. Install the right and left side headliner screws to the #1 bow.

    Tighten:  Tighten the screws to 2 N.m (18 lb in).

    12. Fig 7: Staple Headliner To #1 Bow
    GM790096Courtesy of GENERAL MOTORS CORP.
  12. Staple the headliner to the #1 bow.
  13. Before stapling the top cover to the #1 bow, refer to Folding Top Cover Tension Adjustment - Front .
  14. Reposition the folding top to the original position.
scientia non olet · About LEMON Manuals