LEMON Manuals: Even more car manuals for everyone
Home >> Chevrolet >> 2002 >> Blazer 4D Utility, 4WD, Part Time >> Repair and Diagnosis >> External Pages >> Different car >> Section 1516 (Instrument Panel System Displays, Gauges And Console) >> Repair Instructions >> Trim Pad Replacement - Instrument Panel (I/P) Upper >> Installation Procedure

Installation Procedure

WARNING: This page is about a different car, the 2004 Chevrolet Corvette. However, it is still accessible from the selected car via links, so may be relevant.
    Fig 1: Hazard Warning Switch Electrical Connector
    GM95707Courtesy of GENERAL MOTORS CORP.
  1. Connect the hazard warning switch electrical connector.
    2. Fig 2: Upper Trim Pad At Windshield To LH & RH Side Of Trim Pad At Hinge Pillars
    GM183226Courtesy of GENERAL MOTORS CORP.
  2. Install the IP upper trim pad into position.
    1. Tilt the forward edge of the trim pad down slightly.
    2. SLOWLY begin to move the trim pad into position while guiding the tabs on the LH and RH side of the trim pad past the hinge pillars.
    3. Locate the trim pad by guiding the alignment notch on the underside of the pad onto the alignment pin on the dash panel.
    4. Lower the rearward edge of the pad into place.
  3. Remove the DRL and sunload sensors, if equipped, from the openings in the windshield defroster duct and position above the trim pad.
    4. Fig 3: Upper Trim Pad To Windshield Defroster Duct
    GM95695Courtesy of GENERAL MOTORS CORP.
    NOTE: Refer to Fastener Notice in Cautions and Notices.
  4. Install the screws retaining the upper trim pad to the windshield defroster duct.

    Tighten:  Tighten the IP upper trim pad to windshield defroster duct screws to 1.9 N.m (17 lb in).

  5. Install the screws retaining the upper trim pad to the LH and RH hinge pillars.

    Tighten:  Tighten the IP upper trim pad to LH and RH hinge pillar screws to 2.5 N.m (22 lb in).

    6. Fig 4: Upper Trim Pad To Driver Knee Bolster Outer Bracket & Center Support Bracket
    GM95697Courtesy of GENERAL MOTORS CORP.
  6. Install the screws retaining the upper trim pad to the driver knee bolster outer bracket, the center support bracket and the passenger SIR bracket.

    Tighten: 

    • Tighten the IP upper trim pad to driver knee bolster outer bracket screw to 1.9 N.m (17 lb in).
    • Tighten the IP upper trim pad to IP center support bracket screws to 1.9 N.m (17 lb in).
    • Tighten the IP upper trim pad to passenger SIR bracket screw to 1.9 N.m (17 lb in).

  7. Install the screws retaining the IP cluster bezel to the upper trim pad.

    Tighten:  Tighten the IP cluster bezel to IP upper trim pad screws to 1.3 N.m (12 lb in).

  8. Install the windshield side garnish moldings. Refer to Windshield Side Garnish Molding Replacement in Interior Trim.
  9. Install the windshield defroster grille. Refer to Defroster Grille Replacement .
  10. Install the instrument panel compartment. Refer to Compartment Replacement - Instrument Panel (I/P) .
  11. Install the driver knee bolster trim panel. Refer to Trim Panel Replacement - Knee Bolster .
  12. Install the IP accessory trim plate. Refer to Trim Plate Replacement - Instrument Panel (I/P) Accessory .
  13. Install the console. Refer to Console Replacement .
scientia non olet · About LEMON Manuals