LEMON Manuals: Even more car manuals for everyone
Home >> Chevrolet >> 2002 >> Blazer 4D Utility, 4WD, Part Time >> Repair and Diagnosis >> External Pages >> Different car >> Section 1516 (Instrument Panel System Displays, Gauges And Console) >> Repair Instructions >> Bracket Replacement - Steering Column >> Installation Procedure

Installation Procedure

WARNING: This page is about a different car, the 2004 Chevrolet Corvette. However, it is still accessible from the selected car via links, so may be relevant.
    Fig 1: Steering Column Bracket To I/P Upper Support Beam
    GM95663Courtesy of GENERAL MOTORS CORP.
  1. Install the steering column bracket into position as marked prior to removal.
  2. Install the bolts which secure the steering column bracket to the I/P upper support beam. Do NOT tighten the bolts.
    3. Fig 2: Steering Column Bracket To I/P Lower Support Beam
    GM95665Courtesy of GENERAL MOTORS CORP.
    NOTE: Refer to Fastener Notice in Cautions and Notices.
  3. Install the bolts which secure the steering column bracket to the I/P lower support beam.

    Tighten:  Tighten all of the bolts to 10 N.m (89 lb in).

    4. Fig 3: Clutch Pedal Bracket & Steering Column Bracket
    GM71482Courtesy of GENERAL MOTORS CORP.
  4. Install the clutch pedal bracket stud plate.
  5. Install the nuts to the clutch pedal bracket stud plate.

    Tighten:  Tighten the nuts to 27 N.m (20 lb ft).

    6. Fig 4: View Of Master Cylinder Push Rod To Clutch Pedal
    GM71474Courtesy of GENERAL MOTORS CORP.
  6. Connect the master cylinder push rod to the clutch pedal.
    7. Fig 5: Cruise Control Release Switch & Bracket
    GM71494Courtesy of GENERAL MOTORS CORP.
  7. Position the cruise control release switch and bracket to the steering column bracket.
  8. Install the bracket bolts to the cruise control release switch.

    Tighten:  Tighten the bracket bolts to 12 N.m (106 lb in).

    9. Fig 6: Brake Booster Mounting Nuts At Accelerator Pedal
    GM174198Courtesy of GENERAL MOTORS CORP.
  9. Install the brake booster nuts.

    Tighten:  Tighten the nuts to 29 N.m (21 lb ft).

  10. Connect the master cylinder push rod to the brake pedal.
  11. Install the accelerator pedal assembly with accelerator pedal position sensor. Refer to Accelerator Pedal Position (APP) Sensor Replacement in Engine Controls - 5.7L.
    12. Fig 7: Driver Knee Bolster Outer Bracket To Steering Column Bracket
    GM95667Courtesy of GENERAL MOTORS CORP.
  12. Install the driver knee bolster outer bracket into position as marked prior to removal.
  13. Install the retaining screws to the driver knee bolster outer bracket.

    Tighten:  Tighten the retaining screws to 1.9 N.m (17 lb in).

    14. Fig 8: Bose® Module To Steering Column Bracket
    GM65115Courtesy of GENERAL MOTORS CORP.
  14. If the vehicle is equipped with a Bose® module, position the Bose® module to the steering column bracket.
  15. Install the Bose® module retaining bolts.

    Tighten:  Tighten the retaining bolts to 2.5 N.m (22 lb in).

    16. Fig 9: Bose® Module Electrical/Audio Connector
    GM65118Courtesy of GENERAL MOTORS CORP.
  16. Connect the Bose® module electrical/audio connector.
  17. Install the instrument panel cluster. Refer to Instrument Panel Cluster (IPC) Replacement .
  18. Install the outlet duct to the left side window defogger.
  19. Install the I/P upper trim pad. Refer to Trim Pad Replacement - Instrument Panel (I/P) Upper .
  20. Install the left windshield side garnish molding. Refer to Windshield Side Garnish Molding Replacement in Interior Trim.
  21. Install the steering column to the steering column bracket. Refer to Steering Column Replacement in Steering Wheel and Column.
  22. Install the left lower closeout panel. Refer to Closeout/Insulator Panel Replacement - Left .
    23. Fig 10: Driver Knee Bolster Bracket To Steering Column Bracket
    GM95668Courtesy of GENERAL MOTORS CORP.
  23. Install the driver knee bolster bracket into position as marked prior to removal.
  24. Install the screws which retain the driver knee bolster bracket to the steering column bracket.

    Tighten:  Tighten the screws to 1.9 N.m (17 lb in).

  25. Secure the wiring harness retainers on the ignition switch and hazard warning switch to the driver knee bolster bracket.
  26. Install the ignition switch housing bracket. Refer to Ignition Switch Housing Bracket Replacement .
  27. Install the driver knee bolster trim panel. Refer to Trim Panel Replacement - Knee Bolster .
  28. Install the I/P accessory trim plate. Refer to Trim Plate Replacement - Instrument Panel (I/P) Accessory .
  29. Install the console. Refer to Console Replacement .
  30. Connect the negative battery cable and install the cable bolt.

    Tighten:  Tighten the bolt to 15 N.m (11 lb ft).

  31. Program the transmitters. Refer to Transmitter Programming in Keyless Entry.
  32. Enable the SIR system. Refer to SIR Disabling and Enabling Zone 3 in SIR.
scientia non olet · About LEMON Manuals