LEMON Manuals: Even more car manuals for everyone
Home >> Chevrolet >> 2002 >> Blazer 4D Utility, 4WD, Part Time >> Repair and Diagnosis >> External Pages >> Different car >> Section 1516 (Instrument Panel System Displays, Gauges And Console) >> Repair Instructions >> Bracket Replacement - SIR >> Installation Procedure

Installation Procedure

WARNING: This page is about a different car, the 2004 Chevrolet Corvette. However, it is still accessible from the selected car via links, so may be relevant.
    Fig 1: Passenger Knee Bolster Bracket To Passenger SIR Bracket
    GM95671Courtesy of GENERAL MOTORS CORP.
  1. Install the knee bolster bracket into position as marked prior to removal.
    2. NOTE: Refer to Fastener Notice in Cautions and Notices.
  2. Install the retaining bolts which secure the knee bolster bracket to the SIR bracket.

    Tighten:  Tighten the bolts to 12 N.m (106 lb in).

    3. Fig 2: SIR Module At SIR Bracket
    GM68629Courtesy of GENERAL MOTORS CORP.
  3. Install the SIR module (1) to the SIR bracket (2) as marked prior to removal.
  4. Install the SIR module retaining nuts (3).

    Tighten:  Tighten the nuts to 10 N.m (89 lb in).

    5. Fig 3: SIR Bracket To I/P Upper Support Beam
    GM95672Courtesy of GENERAL MOTORS CORP.
  5. Install the SIR bracket into position as marked prior to removal.
    6. Fig 4: SIR Bracket To I/P Lower Support Beam
    GM95674Courtesy of GENERAL MOTORS CORP.
  6. Install the bolts which secure the SIR bracket to the I/P upper and lower support beams.

    Tighten:  Tighten the bolts to 12 N.m (106 lb in).

    7. Fig 5: Passenger Knee Bolster Bracket To IP Center Support Bracket Retaining Bolts
    GM95682Courtesy of GENERAL MOTORS CORP.
  7. Position the knee bolster bracket to the center support bracket as marked prior to removal.
  8. Install the bolts which secure the knee bolster bracket to the center support bracket.

    Tighten:  Tighten the bolts to 12 N.m (106 lb in).

    9. Fig 6: SIR Module Electrical Connector
    GM68630Courtesy of GENERAL MOTORS CORP.
  9. Connect the SIR module electrical connector.
    10. Fig 7: Electrical Connector Retainer To SIR Bracket
    GM68627Courtesy of GENERAL MOTORS CORP.
  10. Secure the electrical connector retainer to the SIR bracket.
  11. Install the CPA to the SIR module electrical connector.
  12. Secure the I/P harness retainer to the SIR bracket along the hinge pillar. Insert the I/P compartment lamp electrical connector down through the opening in the top of the SIR bracket.
  13. Install the right side window defogger outlet duct.
  14. Install the I/P upper trim pad. Refer to Trim Pad Replacement - Instrument Panel (I/P) Upper .
  15. Adjust the fit of the SIR module to the I/P upper trim pad, if necessary.
  16. Install the I/P compartment. Refer to Compartment Replacement - Instrument Panel (I/P) .
  17. Install the driver knee bolster trim panel. Refer to Trim Panel Replacement - Knee Bolster .
  18. Install the I/P accessory trim plate. Refer to Trim Plate Replacement - Instrument Panel (I/P) Accessory .
  19. Install the console. Refer to Console Replacement .
  20. Enable the SIR system. Refer to SIR Disabling and Enabling Zone 5 in SIR.
scientia non olet · About LEMON Manuals