Transmission Fluid Checking Procedure
WARNING: This page does not describe the selected car, but rather 6 other vehicles, including the 2004 Oldsmobile Bravada, 2004 GMC Envoy XUV, 2004 GMC Envoy XL, 2004 GMC Envoy, and 2004 Chevrolet TrailBlazer. However, it is still accessible from the selected car via links, so may be relevant.
- Start the engine and operate the vehicle for 15 minutes or until the transmission fluid reaches an operating temperature of 82-93° C (180-200° F).
- Park the vehicle on a level surface.
- With your foot on the brake, move the shift lever through each gear range. Pause for about 3 seconds in each range, ending in PARK.
- Apply the parking brake and let the engine idle for 3 minutes.
- Remove the transmission fluid level indicator. Wipe the indicator clean. Insert the indicator. Give the indicator a full twist in order to close.
- Wait 3 seconds and remove the indicator.
- Read both sides of the indicator. The fluid must be within the hot cross-hatched area using the lowest level reading.
Transmission Fluid Checking Procedure
| Step | Action | Yes | No |
|---|---|---|---|
| 1 | Check the fluid color. Is the fluid red in color? |
Go to Step 5 | Go to Step 2 |
| 2 | Is the fluid a non-transparent pink in color? | Go to Step 14 | Go to Step 3 |
| 3 |
IMPORTANT:
Fluid may turn a dark brown in color from normal use. This does not always indicate an oxidation or a contamination issue. Is the fluid a light brown in color? |
Go to Step 5 | Go to Step 4 |
| 4 | Is the fluid black in color and or have a "burnt" smell? | Go to Step 14 | Go to Step 5 |
| 5 | Does the fluid appear as a solid "liquid" and not "foamy" or full of bubbles on level indicator? | Go to Step 6 | Go to Step 6 |
| 6 | Check the fluid level. Proper level should be in middle of the "X" pattern, on level indicator. Is the level OK? |
Go to Step 19 | Go to Step 7 |
| 7 | Is the fluid level high on indicator? | Go to Step 12 | Go to Step 8 |
| 8 | Is the fluid level low on indicator? | Go to Step 9 | Go to Step 4 |
| 9 | Check for any external leak or leaks. Refer to Fluid Leak Diagnosis . Did you find an external leak or leaks? |
Go to Step 10 | Go to Step 11 |
| 10 | Correct leak or leaks as needed. Are any leak or leaks still present? | Go to Step 9 | Go to Step 11 |
| 11 | Add fluid until level is in middle of "X" pattern on the level indicator. Is the level OK? |
Go to Step 19 | Go to Step 6 |
| 12 | Drain fluid until level is in middle of "X" pattern on the level indicator. Is level OK? |
Go to Step 19 | Go to Step 6 |
| 13 | Replace oil cooler and flush lines. Is the replacement complete? |
Go to Step 15 | - |
| 14 |
IMPORTANT:
A small amount of "friction" material in pan bottom is a "normal" condition, but large pieces and or metal particles will require complete transmission overhaul. Drain fluid and remove oil pan to inspect.Is there sign or signs of internal component damage noted in bottom of transmission oil pan? |
Go to Step 16 | Go to Step 13 |
| 15 | Replace the filter and fluid. Refer to Automatic Transmission Fluid/Filter Replacement
. Is the replacement complete? |
Go to Step 6 | - |
| 16 | Flush oil cooler and lines. Refer to Automatic Transmission Oil Cooler Flushing and Flow Test (J 45096) or Automatic Transmission Oil Cooler Flushing and Flow Test (J 35944-A) . Is the Automatic Transmission Oil Cooler Flushing and Flow Test complete? |
Go to Step 17 | - |
| 17 | Overhaul the transmission. Is the Transmission Overhaul Procedure complete? |
Go to Step 18 | - |
| 18 | Add new fluid. Is the procedure complete? |
Go to Step 6 | - |
| 19 | Check the fluid level and correct as necessary. Is the fluid level satisfactory? |
Go to Step 20 | - |
| 20 | If equipped, reset the oil life monitor to 100 percent. Are all of the reset procedures complete? |
System OK | Go to Step 1 |