LEMON Manuals: Even more car manuals for everyone
Home >> Chevrolet >> 2002 >> Blazer 4D Utility, 4WD, Part Time >> Repair and Diagnosis >> External Pages >> Different car >> Section 1458 (Wheel Drive Shafts) >> Repair Instructions >> Wheel Drive Shaft Replacement >> Installation Procedure

Installation Procedure

WARNING: This page does not describe the selected car, but rather 6 other vehicles, including the 2004 Oldsmobile Bravada, 2004 GMC Envoy XUV, 2004 GMC Envoy XL, 2004 GMC Envoy, and 2004 Chevrolet TrailBlazer. However, it is still accessible from the selected car via links, so may be relevant.
    Fig 1: Tying/Untying Front Shock Module/Steering Knuckle To Frame
    GM887942Courtesy of GENERAL MOTORS CORP.
  1. Install the front wheel drive axle front differential assembly.
  2. Remove the mechanics wire or hook from the front shock module/steering
  3. Install the front wheel drive axle in the steering knuckle.
  4. Position the shock module in the shock tower.
  5. Install the shock module into the shock tower
  6. Install the upper ball joint in the upper control arm.
    7. Fig 2: View Of Upper Control Arm To The Steering Knuckle Pinch Bolt And Nut
    GM731542Courtesy of GENERAL MOTORS CORP.
  7. Install the pinch bolt and nut. For the proper torque specification, refer to Steering Knuckle Replacement (RWD) or Steering Knuckle Replacement (4WD) in Front Suspension.
    8. Fig 3: Upper Shock Module Retaining Nuts
    GM886764Courtesy of GENERAL MOTORS CORP.
  8. Install the shock module retaining nuts. For the proper torque specification, refer to Shock Module Replacement in Front Suspension.
  9. Install the front wheel drive shaft retaining.
    10. Fig 4: Removing/Installing Wheel Drive Shaft Nut
    GM731551Courtesy of GENERAL MOTORS CORP.
    NOTE: Refer to Fastener Notice in Cautions and Notices.
  10. Install the new front wheel drive shaft retaining nut.

    Tighten:  Tighten the wheel drive shaft retaining nut to 140 N.m (103 lb ft).

    11. Fig 5: View Of Tie Rod Retaining Nut
    GM687432Courtesy of GENERAL MOTORS CORP.
  11. Install the tie rod end in the steering knuckle. Refer to Rack and Pinion Outer Tie Rod End Replacement in Power Steering System.
    12. Fig 6: Front Stabilizer Bar Link
    GM887945Courtesy of GENERAL MOTORS CORP.
  12. Install the stabilizer bar link. Refer to Stabilizer Shaft Link Replacement in Front Suspension.
    13. Fig 7: Front Brake Hose Retaining Bolt
    GM886462Courtesy of GENERAL MOTORS CORP.
  13. Install the front brake hose retaining bolt. Refer to Brake Hose Replacement - Front in Hydraulic Brakes.
    14. Fig 8: Identifying Wheel Speed Sensor Wiring Harness
    GM886518Courtesy of GENERAL MOTORS CORP.
  14. Install the front wheel speed sensor wiring harness in the retainers.
    15. Fig 9: Locating Connector
    GM886517Courtesy of GENERAL MOTORS CORP.
  15. Reconnect the front wheel speed sensors electrical connector.
    16. Fig 10: Removing/Installing Engine Shield
    GM687450Courtesy of GENERAL MOTORS CORP.
  16. Install the engine protection shield. Refer to Engine Protection Shield Replacement in Frame and Underbody .
    17. Fig 11: View Of Tire/Wheel Assembly, Hub Assembly & Wheel Nuts
    GM656803Courtesy of GENERAL MOTORS CORP.
  17. Install the tire and wheel assembly. Refer to Tire and Wheel Removal and Installation in Tires and Wheels.
  18. Lower the vehicle. Refer to Lifting and Jacking the Vehicle in General Information.
scientia non olet · About LEMON Manuals