Theft Deterrent Alarm Inoperative
WARNING: This page does not describe the selected car, but rather 6 other vehicles, including the 2004 Oldsmobile Bravada, 2004 GMC Envoy XUV, 2004 GMC Envoy XL, 2004 GMC Envoy, and 2004 Chevrolet TrailBlazer. However, it is still accessible from the selected car via links, so may be relevant.
IMPORTANT:
Before attempting to diagnose the Theft Deterrent Alarm, insure that the ASM Part A, and ASM Part B are enabled in the Dash Integration Module (DIM) Set Options menu.
Theft Deterrent Alarm Inoperative
| Step | Action | Values | Yes | No |
|---|---|---|---|---|
| Schematic Reference: Theft Deterrent System Schematics Connector End View Reference: Theft Deterrent System Connector End Views DEFINITION: THE Theft Deterrent Alarm does not sound when the CTD system is in alarm mode, Or: The Theft Deterrent Alarm sounds when the CTD system is not in alarm mode. |
||||
| 1 | Did you perform the Theft Deterrent System Diagnostic System Check? | - | Go to Step 2 | Go to Diagnostic System Check - Theft Deterrent |
| 2 | Were you sent here from Content Theft Deterrent (CTD) Alarm Mode Inoperative? | - | Go to Step 3 | Go to Content Theft Deterrent (CTD) Alarm Mode Inoperative |
| 3 | Does the Theft Deterrent Alarm sound when the CTD system is not in alarm mode? | - | Go to Step 4 | Go to Step 5 |
| 4 | Does the Theft Deterrent Alarm sound when the ignition is ON? | - | Go to Step 6 | Go to Step 7 |
| 5 | Disconnect the Theft Deterrent Alarm harness connector. Does the Theft Deterrent Alarm sound? |
- | Go to Step 8 | Go to Step 9 |
| 6 |
|
- | Go to Step 9 | Go to Step 13 |
| 7 | Measure the voltage of the hazard switch signal circuit at the Theft Deterrent Alarm harness connector. Is the voltage near the specified value? |
12 V | Go to Step 9 | Go to Step 11 |
| 8 | Test the Theft Deterrent Alarm hazard switch signal circuit for a short to voltage. Refer to Circuit Testing
and Wiring Repairs
in Wiring Systems. Did you find and correct the condition? |
- | Go to Step 18 | Go to Step 12 |
| 9 | Test the Theft Deterrent Alarm ground circuit for an open. Refer to Circuit Testing
and Wiring Repairs
in Wiring Systems. Did you find and correct the condition? |
- | Go to Step 18 | Go to Step 10 |
| 10 | Test the Theft Deterrent Alarm battery positive voltage circuit for an open or a short to ground. Refer to Circuit Testing
and Wiring Repairs
in Wiring Systems. Did you find and correct the condition? |
- | Go to Step 18 | Go to Step 14 |
| 11 | Test the Theft Deterrent Alarm hazard switch signal circuit for an open or a short to ground. Refer to Circuit Testing
and Wiring Repairs
in Wiring Systems. Did you find and correct the condition? |
- | Go to Step 18 | Go to Step 15 |
| 12 | Repair the short to voltage on the Theft Deterrent Alarm Ignition 1 voltage circuit. Refer to Circuit Testing
and Wiring Repairs
in Wiring Systems. Did you complete the repair? |
- | Go to Step 18 | - |
| 13 | Repair the short to ground or the open in the Theft Deterrent Alarm Ignition 1 voltage circuit. Refer to Circuit Testing
and Wiring Repairs
in Wiring Systems. Did you complete the repair? |
- | Go to Step 18 | - |
| 14 | Inspect for a loose or poor connection at the harness connector of the Theft Deterrent Alarm. Refer to Testing for Intermittent Conditions and Poor Connections
and Connector Repairs
in Wiring Systems. Did you find and correct the condition? |
- | Go to Step 18 | Go to Step 16 |
| 15 | Inspect for a loose or poor connection at the harness connector of the Body Control Module (BCM). Refer to Testing for Intermittent Conditions and Poor Connections
and Connector Repairs
in Wiring Systems. Did you find and correct the condition? |
- | Go to Step 18 | Go to Step 17 |
| 16 | Replace the Theft Deterrent Alarm. Refer to Theft Deterrent Alarm Replacement . Did you complete the repair? |
- | Go to Step 18 | - |
| 17 | Replace the BCM. Refer to Body Control Module Replacement
in Body Control System. Did you complete the repair? |
- | Go to Step 18 | - |
| 18 | Operate the system in order to verify the repair. Did you correct the condition? |
- | System OK | Go to Step 3 |