LEMON Manuals: Even more car manuals for everyone
Home >> Chevrolet >> 2002 >> Blazer 4D Utility, 4WD, Part Time >> Repair and Diagnosis >> External Pages >> Different car >> Section 1401 (Instrument Panel System Displays, Gauges And Console) >> Diagnostic Information and Procedures >> DTC B0560: Tachometer Circuit >> Conditions for Clearing the DTC

Conditions for Clearing the DTC

WARNING: This page does not describe the selected car, but rather 6 other vehicles, including the 2004 Oldsmobile Bravada, 2004 GMC Envoy XUV, 2004 GMC Envoy XL, 2004 GMC Envoy, and 2004 Chevrolet TrailBlazer. However, it is still accessible from the selected car via links, so may be relevant.
DTC B0560 Diagnostic Table

Step Action Yes No
Schematic Reference:  Instrument Cluster Schematics  
Connector End View Reference:  Instrument Panel, Gages, and Console Connector End Views  ,  Powertrain Control Module (PCM) Connector End Views  , or  Powertrain Control Module (PCM) Connector End Views 
1 Did you perform the IPC Diagnostic System Check? Go to Step 2  Go to Diagnostic System Check - Instrument Cluster 
2
  1. Install a scan tool.
  2. Start the engine.
  3. With the scan tool, observe the Engine Speed parameter in the IPC Data 1 data list.
Does the Engine Speed parameter match the tachometer display?		 Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems Go to Step 3 
3
  1. Turn the ignition OFF.
  2. Disconnect the following PCM connector:
    • C1 (LL8)
    • C2 (LM4)
  3. Install the J 33431-C  Signal Generator and Instrument Panel Tester lead to the engine speed signal circuit at the PCM harness connector, and the other lead to a good ground. See Special Tools and Equipment .
  4. Turn the ignition ON, with the engine OFF.
  5. Set the J 33431-C  Signal Generator and Instrument Panel Tester to generate a tachometer signal. See Special Tools and Equipment .
Does the vehicle tachometer indicate an RPM reading?		 Go to Step 5  Go to Step 4 
4 Test the engine speed signal circuit for an open, a short to voltage or a short to ground. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.
Did you find and correct the condition?		 Go to Step 9  Go to Step 6 
5 Inspect for poor connections at the PCM connector. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.
Did you find and correct the condition?		 Go to Step 9  Go to Step 7 
6 Inspect for poor connections at the harness connector of the IPC. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.
Did you find and correct the condition?		 Go to Step 9  Go to Step 8 
7
IMPORTANT: Program the replacement PCM.
Replace the PCM. Refer to Powertrain Control Module (PCM) Replacement in Engine Controls - 4.2L or to Powertrain Control Module (PCM) Replacement in Engine Controls - 4.8L, 5.3L, or 6.0L.
Did you complete the replacement?		 Go to Step 9  -
8
IMPORTANT: Program the replacement IPC.
Replace the IPC. Refer to Instrument Panel Cluster (IPC) Replacement .Did you complete the replacement?		 Go to Step 9  -
9
  1. Use the scan tool in order to clear the DTC's.
  2. Operate vehicle within the conditions for running this DTC as specified in the supporting text.
Does the DTC reset?		 Go to Step 2  System OK
scientia non olet · About LEMON Manuals