LEMON Manuals: Even more car manuals for everyone
Home >> Chevrolet >> 2002 >> Blazer 4D Utility, 4WD, Part Time >> Repair and Diagnosis >> External Pages >> Different car >> Section 1383 (Engine Control System Diagnosis (DTC P0130 To DTC P0456) -- 1.8L (LNK)) >> Diagnosis >> DTC P0133 >> Test Description

Test Description

WARNING: This page is about a different car, the 2004 Pontiac Vibe. However, it is still accessible from the selected car via links, so may be relevant.

The numbers below refer to the step numbers in the diagnostic table.

  1. 1:  The Diagnostic System Check-Engine Controls prompts the technician to complete some basic checks and store the Freeze Frame data on the scan tool if applicable. This creates an electronic copy of the data taken when the fault occurred. The information is then stored in the scan tool for later reference.
  2. 2:  This step checks whether the malfunction that caused the DTC P0133 is still present. Operating the vehicle in Check Mode enhances the diagnostic capabilities of the PCM. The HO2S 1 diagnostic can be monitored on the scan tool under the I/M System Information. When the HO2S test displays a YES status, indicating that the heated oxygen sensor system diagnostic is completed, check for a DTC P0133 in the Last Test Failed screen of the scan tool. If there is no DTC P0133 displayed the HO2S diagnostic has run and passed, indicating that no malfunction was present this time. The DTCs MUST be cleared in order to view the Current Status of the system diagnostics being performed. Do not forget that the I/M System Information tests only indicate that the test has run, not whether the test passed or failed. The Last Test Failed screen must be checked for related DTCs in order to determine the outcome of the diagnostic test involved.
  3. 5:  In this step the DMM is used as a low current voltage source taking the place of the HO2S. This step verifies whether the PCM is able to receive and process a signal from the HO2S 1.
DTC P0133

Step Action Values Yes No
Schematic Reference:  Engine Controls Schematics 
1  Did you perform the Diagnostic System Check-Engine Controls? - Go to Step 2  Go to Diagnostic System Check - Engine Controls
2 
  1. Perform the scan tool Clear DTC Information function.
  2. Place the vehicle into Check mode, using the scan tool. Refer to Service Bay Test .
  3. Operate the vehicle within the Freeze Frame conditions as specified, or until the HO2S/O2S test is complete. Refer to the supporting text.
Did DTC P0133 set?		 - Go to Step 3  Go to Diagnostic Aids
3
  1. Visually and physically inspect for the following items:
    • The HO2S 1 is securely installed.
    • Any corrosion on terminals
    • The proper terminal tension at the HO2S 1 and at the PCM
    • Any damaged wiring
  2. Repair as necessary.
Was a repair necessary?		 - Go to Step 11  Go to Step 4 
4
  1. Check the exhaust system for an exhaust leak near the engine.
  2. Repair as necessary.
Was an exhaust leak found?		 - Go to Step 11  Go to Step 5 
5 
  1. Disconnect the HO2S 1 electrical connector located behind the front floor console. Refer to Heated Oxygen Sensor Replacement - Position 1 .
  2. Turn ON the ignition, with the engine OFF.
  3. Set a DMM to measure DC millivolts.
  4. Place the positive lead of the DMM on battery positive voltage, and the negative lead on the HO2S 1 sensor input circuit terminal on the engine harness side.
  5. Observe the HO2S 1 parameter on the scan tool.
Is the voltage more than the specified value?		 1155 mV Go to Step 6  Go to Step 7 
6
  1. Connect a test lamp to battery voltage.
  2. Probe the HO2S 1 ground circuit terminal at the HO2S connector on the engine harness side.
Does the test lamp illuminate?		 - Go to Step 9  Go to Step 8 
7
  1. Check for an open or a short in the HO2S 1 input circuit between the HO2S 1 and the PCM connector.
  2. Repair as necessary. Refer to Wiring Repairs in Wiring Systems.
Was a repair necessary?		 - Go to Step 11  Go to Step 10 
8 Repair the open in the HO2S 1 ground circuit between the HO2S 1 and G104. Refer to Wiring Repairs in Wiring Systems.
Is the action complete?		 - Go to Step 11  -
9
  1. Check for and repair any possible causes of HO2S contamination including the following possible causes:
    • Fuel contamination
    • Use of an improper RTV sealant
    • Engine oil or coolant consumption
  2. Replace the HO2S 1. Refer to Heated Oxygen Sensor Replacement - Position 1 .
Is the action complete?		 - Go to Step 11  -
10 Replace the PCM. Refer to Powertrain Control Module (PCM) Replacement .
Is the action complete?		 - Go to Step 11  -
11
  1. Use the scan tool in order to clear the DTCs.
  2. Turn OFF the ignition for 30 seconds.
  3. Start the engine.
  4. Operate the vehicle within the Conditions for Running the DTC or until the HO2S/O2S test is complete. Review the supporting text.
Did the DTC run and pass?		 - Go to Step 12  Go to Step 2 
12 With a scan tool, observe the stored information, Capture Info.
Does the scan tool display any DTCs that you have not diagnosed?		 - Go to Diagnostic Trouble Code (DTC) List System OK
scientia non olet · About LEMON Manuals