LEMON Manuals: Even more car manuals for everyone
Home >> Chevrolet >> 2002 >> Blazer 4D Utility, 4WD, Part Time >> Repair and Diagnosis >> External Pages >> Different car >> Section 1327 (Automatic Transmission - Mu4 (Introduction, Service & Replacement)) >> Diagnostic Information and Procedures >> DTC P0756 >> Test Description

Test Description

WARNING: This page is about a different car, the 2004 Pontiac Vibe. However, it is still accessible from the selected car via links, so may be relevant.

The numbers below refer to the step numbers on the diagnostic table.

  1. 1:  The Powertrain OBD System Check prompts the technician to complete some basic checks and store the freeze frame data on the scan tool if applicable. This creates an electronic copy of the data taken when the fault occurred. The information is then stored in the scan tool for later reference.
  2. 3:  This step checks for proper shift points.
  3. 5:  This step checks for a leaky shift solenoid #2.
  4. 6:  This step checks for a stuck closed shift solenoid #2.
  5. 8:  This step checks the condition of the valve body assembly.
  6. 9:  This step checks for a faulty PCM.
DTC P0756

Step Action Yes No
Schematic Reference: Automatic Transmission Controls Schematics 
1  Was the On-Board Diagnostic (OBD) System Check performed? Go to Step 2  Go to Diagnostic System Check - Engine Controls in Engine Controls
2
  1. Install a scan tool.
  2. Turn the ignition to ON, leaving the engine OFF.
  3. Perform the scan tool Clear DTC Information function.
  4. Operate the vehicle within the Freeze Frame conditions as observed.
Does the scan tool display any other DTCs in addition to DTC P0756?		 Go to applicable DTC table Go to Step 3 
3  Perform Upshifts and Torque Converter Clutch Apply Procedure in Road Test Procedure  in order to diagnose mechanical condition of transaxle.
Is action complete?		 Go to Step 4  -
4 Perform DTC Confirmation Procedure.
Did this DTC reset?		 Go to Step 5  Go to Step 11 
5 
  1. Remove shift solenoid #2.
  2. Apply 490 kPa (71 psi) of compressed air into the shift solenoid #2 inlet port.
Did the shift solenoid #2 outlet port open and did air escape?		 Go to Step 6  Go to Step 12 
6 
  1. Apply 12V to shift solenoid #2 (positive to wire, negative to case).
  2. Apply 490 kPa (71 psi) of compressed air into the shift solenoid inlet.
Did the shift solenoid #2 outlet port open and did air escape?		 Go to Step 7  Go to Step 12 
7 Refer to DTC P1780  for diagnosis of the PNP switch.
Is the action complete?		 Go to Step 8  -
8  Remove the valve body and inspect the passages for any obstructions/restrictions. Refer to Solenoids and Wiring Harness Replacement .
Is the valve body in good condition?		 Go to Step 9  Go to Step 10 
9 
  1. Install a known good PCM. Refer to Powertrain Control Module (PCM) Replacement in Engine Controls.
  2. Perform the DTC Confirmation Procedure.
Does this DTC reset?		 Go to Step 13  Go to Step 14 
10 Repair or overhaul valve body assembly. Refer to Automatic Transmission Controls Schematics .
Is the action complete?		 Go to Step 15  Go to Step 14 
11 A malfunction is not present at this time. Refer to Diagnostic Aids.
Is the action complete?		 System OK -
12 Replace shift solenoid #2.
Is the action complete?		 Go to Step 15  -
13 Refer to Road Test Procedure  for further diagnosis of the transaxle's performance. Repair as necessary.
Is the action complete?		 Go to Step 15  -
14 Replace Powertrain Control Module (PCM). Refer to Powertrain Control Module (PCM) Replacement in Engine Controls.
Is the action complete?		 Go to Step 15  -
15 Perform the DTC Confirmation Procedure.
Are any DTCs displayed on the Scan Tool?		 Go to applicable DTC table System OK
scientia non olet · About LEMON Manuals