LEMON Manuals: Even more car manuals for everyone
Home >> Chevrolet >> 2002 >> Blazer 4D Utility, 4WD, Part Time >> Repair and Diagnosis >> External Pages >> Different car >> Section 1091 (Instrument Panel System Displays, Gauges And Console) >> Diagnostic Information and Procedures >> Driver Information Center (DIC) Switch(es) Inoperative

Driver Information Center (DIC) Switch(es) Inoperative

WARNING: This page is about a different car, the 2004 Pontiac Aztek and 2004 Buick Rendezvous. However, it is still accessible from the selected car via links, so may be relevant.
Driver Information Center (DIC) Switch(es) Inoperative

Step Action Yes No
Schematic Reference:  Instrument Cluster Schematics  
1 Did you perform the IPC Diagnostic System Check? Go to Step 2  Go to Diagnostic System Check - Instrument Cluster 
2
  1. Turn ON the ignition, with the engine OFF.
  2. Install a scan tool.
  3. With a scan tool, observe the DIC switch parameters in the IPC Inputs data list.
  4. Press and release each of the DIC switches.
Does the scan tool display On when each switch is pressed and Off when each switch is released?		 Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems Go to Step 3 
3 Does the scan tool display Off when each switch is pressed? Go to Step 9  Go to Step 4 
4 Does the scan tool always display On for the suspect switch even when the switch is released? Go to Step 5  Go to Step 6 
5
  1. Turn OFF the ignition.
  2. Disconnect the DIC switch connector.
  3. Turn ON the ignition, with the engine OFF.
  4. With a scan tool, observe the suspect DIC switch parameter.
Does the scan tool display On for the suspect switch?		 Go to Step 7  Go to Step 12 
6
  1. Turn OFF the ignition.
  2. Disconnect the DIC switch connector.
  3. Connect a 3 amp fused jumper wire between the signal circuit of the suspect DIC switch and a good ground. Refer to Circuit Testing in Wiring Systems.
  4. Turn ON the ignition, with the engine OFF.
  5. With a scan tool, observe the suspect DIC switch parameter.
Does the scan tool display On for the suspect switch?		 Go to Step 10  Go to Step 8 
7 Test the signal circuit of the suspect DIC switch for a short to ground. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.
Did you find and correct the condition?		 Go to Step 14  Go to Step 11 
8 Test the signal circuit of the suspect DIC switch for an open or high resistance. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.
Did you find and correct the condition?		 Go to Step 14  Go to Step 11 
9 Test the ground circuit of the DIC switch for an open or high resistance. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.
Did you find and correct the condition?		 Go to Step 14  Go to Step 10 
10 Inspect for poor connections at the harness connector of the DIC switch. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.
Did you find and correct the condition?		 Go to Step 14  Go to Step 12 
11 Inspect for poor connections at the IPC. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.
Did you find and correct the condition?		 Go to Step 14  Go to Step 13 
12 Replace the DIC switch. Refer to Driver Information Center Switch Replacement (Rendezvous)  or Driver Information Center Switch Replacement (Aztek) .
Did you complete the replacement?		 Go to Step 14  -
13
IMPORTANT: Perform the compass calibration and variance procedure on the replacement IPC.
Replace the IPC. Refer to Instrument Panel Cluster (IPC) Replacement .Did you complete the replacement?		 Go to Step 14  -
14 Operate the system in order to verify the repair.
Did you correct the condition?		 System OK Go to Step 2 
scientia non olet · About LEMON Manuals