LEMON Manuals: Even more car manuals for everyone
Home >> Chevrolet >> 2002 >> Blazer 4D Utility, 4WD, Part Time >> Repair and Diagnosis >> External Pages >> Different car >> Section 1034 (Automatic Transmission - 4L60-E/4L65-E (Introduction, Service & Replacement)) >> Repair Instructions >> Filler Tube and Seal Replacement >> Installation Procedure

Installation Procedure

WARNING: This page is about a different car, the 2004 GMC Sierra and 2004 Chevrolet Silverado. However, it is still accessible from the selected car via links, so may be relevant.
  1. Install a NEW seal to the indicator tube.
  2. Install the oil level indicator tube, if equipped with RPO HP2.
    Fig 1: Installing A New Seal To The Indicator Tube (With RPO HP2)
    GM1284302Courtesy of GENERAL MOTORS CORP.
    3. Fig 2: View Of Oil Level Indicator Tube & Seal
    GM396798Courtesy of GENERAL MOTORS CORP.
  3. Install a NEW seal to the indicator tube.
  4. Install the oil level indicator tube.
    5. NOTE: Refer to Fastener Notice in Cautions and Notices.
    Fig 3: Installing The Indicator Tube Bolt (With RPO HP2)
    GM1284303Courtesy of GENERAL MOTORS CORP.
  5. Install the indicator tube bolt, if equipped with RPO HP2.

    Tighten:  Tighten the bolt to 18 N.m (13 lb ft).

    6. Fig 4: View Of Oil Level Indicator Tube Nut
    GM396797Courtesy of GENERAL MOTORS CORP.
  6. Install the indicator tube nut.

    Tighten:  Tighten the nut to 18 N.m (13 lb ft).

  7. Remove the plugs from the transmission oil cooler line fittings.
  8. Connect the transmission oil cooler lines. Refer to Transmission Fluid Cooler Line Quick Connect Fitting .
    Fig 5: View Of Transmission Oil Cooler Lines
    GM396804Courtesy of GENERAL MOTORS CORP.
  9. Install the exhaust pipe hanger bracket and bolts.

    Tighten:  Tighten the bolts to 17 N.m (12 lb ft).

  10. Instal the insulator and nuts to the bracket.

    Tighten:  Tighten the nuts to 17 N.m (12 lb ft).

    Fig 6: View Of Heat Shield/Exhaust Pipe Hanger Bracket & Bolts
    GM858548Courtesy of GENERAL MOTORS CORP.
    11. Fig 7: View Of Right Exhaust Pipe Nuts
    GM858553Courtesy of GENERAL MOTORS CORP.
  11. Tighten the right exhaust pipe nuts.

    Tighten:  Tighten the nuts to 50 N.m (37 lb ft).

    12. Fig 8: View Of Left Exhaust Manifold Pipe & Nuts
    GM858550Courtesy of GENERAL MOTORS CORP.
  12. Tighten the left exhaust pipe nuts.

    Tighten:  Tighten the nuts to 50 N.m (37 lb ft).

    13. Fig 9: View Of Transmission Crossmember
    GM702036Courtesy of GENERAL MOTORS CORP.
  13. Install the transmission crossmember.
  14. Install the transmission crossmember bolts/nuts.

    Tighten:  Tighten the bolts/nuts to 95 N.m (70 lb ft).

    15. Fig 10: Installing The Transmission Mount Nut
    GM858997Courtesy of GENERAL MOTORS CORP.
  15. Install the transmission mount nut.

    Tighten:  Tighten the nut to 50 N.m (37 lb ft).

  16. Remove the support from the transmission.
  17. Lower the vehicle.
  18. Install the transmission oil level indicator.
  19. Lock the transmission oil level indicator.
scientia non olet · About LEMON Manuals